Videonics AB-1 Edit Suite страница 102 Скачать руководство пользователя | Manualshive

Страница: 102 / 151

background image

amount to use so that Edit Suite sends the GPI trigger at the correct time.

The GPI-T choice is used only for specifying the offset value for the trigger pulses. See GPI Events in
Chapter 5 for more information. The MX-1 and third-party mixers/switchers cannot be used with the
GPI-T port.

To display the Configuration Menu, from Setup Menu 1, move the cursor to CONFIG and press [OK].
To return to Setup Menu 1 from the Configuration Menu, press [SETUP].

Setup Menu 1 Configuration Menu

To access the GPI-M or GPI-T parameters, move the cursor to GPI-M or GPI-T in the Configuration
Menu and press [OK].

GPI-M Choices GPI-T

The GPI-M Choices above show each of the choices for the GPI-M port. To cycle between the choices,
with the cursor in the GPI-M field, press [CHG]. Select MX-1 if a Videonics MX-1 is attached to the
GPI-M port; select MIXER if a third-party mixer or switcher is attached; select GPI if a GPI-device
other than a mixer or switcher is used, or if no device is attached to the port.

To change the sign (+ or -) for either of the GPI-M or GPI-T offset values, move the cursor to the sign
field and press [CHG].

To change the Offset values for GPI-M or GPI-T, move the cursor to the offset value field, press [CHG]
to activate the numeric keys, enter the offset amount (or turn the jog/shuttle to change the current value),

«
...
100
101
102
103
104
...
»

Содержание AB-1 Edit Suite
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для AB-1 Edit Suite

NG Network Access Client SP4

Бренд: Barracuda Networks Страницы: 268

AMD-8151 HyperTransport AGP3.0

Бренд: AMD Страницы: 16

Бренд: Arturia Страницы: 10

Бренд: Sling Media Страницы: 112

Бренд: GE Страницы: 82

Configuring Arrays

Бренд: HP Страницы: 132

Бренд: HP Страницы: 26

Бренд: HP Страницы: 35

460C - Deskjet Color Inkjet Printer

Бренд: HP Страницы: 24

Бренд: HP Страницы: 201

BB118BV - StorageWorks Data Protector Express Package

Бренд: HP Страницы: 365

BB118BV - StorageWorks Data Protector Express Package

Бренд: HP Страницы: 35

2605dtn - Color LaserJet Laser Printer

Бренд: HP Страницы: 372

e-diagtools 4.0

Бренд: HP Страницы: 74

Бренд: Seagate Страницы: 1

Бренд: Billion Страницы: 18

Бренд: APPLIED ACOUSTICS SYSTEMS Страницы: 60

ASSET MANAGEMENT SUITE 7.0

Бренд: Symantec Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды