Videonics AB-1 Edit Suite страница 113 Скачать руководство пользователя | Manualshive

Страница: 113 / 151

background image

GPI-triggered title was
not recorded.

Check the start time for the GPI Event. If it is
outside the IN and OUT times for the
corresponding scene, it will not be triggered. If
the event occurs close to the OUT time, the title
may not be able to play before the recorder is
paused. Move the GPI time ahead a few
seconds.

See GPI Events in Chapter 5 for more
information.

Jog fails to control the
VCR.

Does the VCR/camcorder have jog capabilities?
If not, Edit Suite will not be able to jog the
video.

Ensure the VCR is powered on and that the
VCRs counter displays a time code value.
Select a different source and then reselect the
current source.

Turn the shuttle past the Pause position and
then back to Pause. If this does not work, try
pressing the PLAY transport key.

If the jog worked previously, remove and then
reattach Edit Suite's power cord. Note: Before
removing power from Edit Suite, disconnect
Edit Control cables to VCRs with PANA
protocol.

Inaccurate scene

If you have not already done the fine-tuning
procedures in Chapter 7, do them.

If the tuning procedures do not fix the problem,
increase the PLY(play) Advanced Parameter by
five (5) seconds, but be sure that the REW
(rewind) parameter value is equal to or greater
than PLY and that both are less than the FFD
(fast forward) parameter.

IN OFFSET has no
effect on the in-point
accuracy.

The IN OFFSET for Play VCRs adjusts the start
time for the "B" source in an A/B Roll. See
Chapter 7, Fine Tuning.

«
...
111
112
113
114
115
...
»

Содержание AB-1 Edit Suite
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для AB-1 Edit Suite

COLFUSION MX 7 - INSTALLING AND USING COLDFUSION...

Бренд: MACROMEDIA Страницы: 72

Бренд: M-Audio Страницы: 32

Бренд: Arturia Страницы: 125

Бренд: YOKOGAWA Страницы: 29

Бренд: Alcatel Страницы: 4

Centralized Network Management

Бренд: Asus Страницы: 41

Бренд: Asus Страницы: 11

Бренд: Asus Страницы: 72

GigaX 1024P User's

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 83

Бренд: Asus Страницы: 721

ASWM Enterprise

Бренд: Asus Страницы: 106

Бренд: Asus Страницы: 118

Lamborghini VX2

Бренд: Asus Страницы: 88

Бренд: Asus Страницы: 58

Бренд: Asus Страницы: 90

Бренд: Asus Страницы: 73

Бренд: Asus Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды