Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 72

background image

22

20306743

KSTDV Series Gas Fireplace

GAS PIPE INSTALLATION

CAUTION

A manual shutoff valve must be installed
upstream of the appliance. Union tee
and plugged 1/8" NPT pressure tapping
point should be installed upstream of the
appliance. Figure 28

CAUTION

Use pipe joint sealant that is resistant to
liquid petroleum (LP) gas.

3" Minimum

Pipe Nipple

Cap

Figure 28 -
Gas Connection

Tee Joint

Approved Flexible
Gas Line

CSA Design-Certi

fi

ed Equipment Shutoff Valve

with 1/8" NPT Tap*

Sediment Trap/Drip Leg

Natural Gas

From Gas Meter

(4.0" w.c. to 10.5" w.c. Pressure)

Propane/LP

From External Regulator

(11" w.c. to 13" w.c. Pressure)

INSTALL GAS SUPPLY LINE

NOTE : The gas line connection may be made using 1/2"
rigid tubing or an approved

fl

ex connector. Since some

municipalities have additional local codes it is always best
to consult your local authorities and the current edition of
the National Fuel Gas Code ANSI.Z223.1, NFPA54. In
Canada CSA-B149 (1 or 2) Installation Code.
A listed manual shutoff valve must be installed upstream of
the appliance. Union tee and plugged 1/8" NPT pressure
tapping point should be installed upstream of the appliance.

Figure 28

IMPORTANT:

Install main gas valve (equipment shutoff

valve) in an accessible location. The main gas valve is for
turning on or shutting off the gas to the

fi

replace.

Check your building codes for any special requirements for
locating equipment shutoff valve to

fi

replaces.

Only persons licensed to work with gas
piping may make the necessary gas
connections to this appliance.

W

ARNING

Apply pipe joint sealant lightly to male threads. This will
prevent excess sealant from going into pipe. Excess seal-
ant in pipe could result in clogged burner system valves.
We recommend that you install a sediment trap/drip leg in
supply line as shown in

Figure 28

. Locate sediment trap/

drip leg where it is within reach for cleaning. Install in piping
system between fuel supply and burner system. Locate
sediment trap/drip leg where trapped matter is not likely to
freeze. A sediment trap traps moisture and contaminants.
This keeps them from going into the burner system gas con-
trols. If sediment trap/drip leg is not installed or is installed
wrong, burner system may not run properly.

«
...
20
21
22
23
24
...
»

Содержание KSTDV500(N/P)TSCSB









































































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренд: Nectre Fireplaces Страницы: 6

Бренд: Valor Fires Страницы: 56

Бренд: Valor Fires Страницы: 56

Бренд: Valor Страницы: 72

Бренд: Valor Страницы: 38

Paul Agnew Designs ilektro Series

Бренд: Living Fire Страницы: 4

Heatilator Icon Series

Бренд: Heatilator Страницы: 2

Бренд: Belleze Страницы: 12

Бренд: Travis Industries Страницы: 8

Бренд: CC Products Страницы: 7

Imperial Carousel

Бренд: Malm Fireplaces Страницы: 8

Ascent Linear BL56

Бренд: Napoleon Страницы: 132

Бренд: Adobelite Страницы: 23

Бренд: Heat&Glo Страницы: 49

Бренд: KEKAI Страницы: 46

Бренд: Uberhaus Страницы: 7

Бренд: GlammFire Страницы: 13

KIT Glamm H3D 700

Бренд: GlammFire Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды