Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 27

Страница: 27 / 72

20306743

KSTDV Series Gas Fireplace

FINAL INSTALLATION

GLASS FRAME REMOVAL

NOTE:

You must

rst remove the safety barrier before

you remove the glass frame. To remove the barrier, lift
up and pull out until the tabs are clear of their corre-
sponding slots on the

rebox. Then proceed to remove

the glass frame by:
1. Remove the plate located in front of the glass at the

bottom.

2. Remove rod provided for screen assembly located

beneath the cover plate.

3. Rotate the access doors on the right and left side of the

glass toward the glass.

4. Remove glass frame by releasing the three latches

located at the top of the

rebox. Tilt glass away from the

unit, lift glass frame up and away from the unit.

Figure

Each clamp has a quick spring force. When
reinstalling clamps, keep fi ngers clear.

Figure 33 -
Remove Safety Barrier and Glass Frame

DANGER

HOT GLASS

WILL

CAUSE BURNS

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and shall

be installed for the protection of children and

other at risk individuals.

20306543

Glass Frame

Safety Barrier

Содержание KSTDV500(N/P)TSCSB









































































Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды

Vermont Castings KSTDV500(N/P)TSCSB, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды