Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 72

background image

20306743

23

KSTDV Series Gas Fireplace

CHECK GAS PRESSURE

1. Check gas type. The gas supply must be the same as

stated on the appliance’s rating decal. If the gas supply
is different from the

fi

replace,

STOP!

Do not install the

appliance. Contact your dealer immediately.

2. To ease installation, a 24" (610 mm)

fl

ex line with manual

shut-off valve has been provided with on this appliance.
Install and attach 1/2" gas line onto shut-off valve.

3. After completing gas line connection, purge air from

gas line and test all gas joints from the gas meter to the

fi

replace for leaks. Use a solution of 50/50 water and

soap solution or a gas sniffer.

4. To check gas pressures at valve, turn captured screw

counter clockwise 2 or 3 turns and then place tubing
to pressure gauge over test point. Turn unit to high.

Figure 29.

After taking pressure reading, be sure and

turn captured screw clockwise

fi

rmly to reseal. Do not

over torque. Check test points for gas leaks.

ELECTRICAL WIRING

General

1. This

fi

replace is equipped with the Signature Control

valve which operates on 6 volts. The AC module plugs
into the

fi

replace junction box A/C power supply. Four

(4) “AA” batteries are used for back up during power
outages.

2. The Signature Command System can also be operated

without A/C power. The system can run on four (4) “AA”
batteries for approximately six (6) months under normal
use.

3. A/C power must be used to power the A/C module,

blowers, lights and AUX accessories used with this

fi

replace.

Optional Accessory Requirements

1. This

fi

replace may be used with a wall switch and/or

Signature Command wireless controls.

2. The command center control may be mounted on the

wall with the use of the SCSWEK 15ft. wall mount
extension kit.

Figure 29 -
Signature Command Valve

W

ARNING

Do not use open fl ame to check for gas
leaks.

Pilot Adjustment
Screw

Pressure Outlet

FP1909a

Pressure Inlet

CHECKING GAS PRESSURE AND ELECTRICAL INSTALLATION

W

ARNING

E l e c t r i c a l c o n n e c t i o n s s h o u l d o n l y
be performed by a qualified, licensed
electrician. Main power must be off when
connecting to main electrical power supply
or performing service. All wiring shall be
in compliance with all local, city and state
codes. The appliance, when installed, must
be electrically grounded in accordance with
local codes or in the absence of local codes,
with the National Electrical Code ANSI/NFPA
70 (latest edition) and Canadian Electrical
Code, CSA C22.1.

CAUTION

Label all wires before disconnecting when
servicing controls. Wiring errors can cause
improper and dangerous operation.

«
...
21
22
23
24
25
...
»

Содержание KSTDV500(N/P)TSCSB









































































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренд: PSF Страницы: 2

Бренд: Amantii Страницы: 21

Бренд: Napoleon Страницы: 2

Бренд: Solas Страницы: 35

Бренд: Astria Страницы: 44

Бренд: Starfire Страницы: 11

Бренд: Napoleon Страницы: 4

1060 LED INSET ELECTRIC FIRE

Бренд: Ekofires Страницы: 7

Бренд: Coleman Страницы: 2

Бренд: Coleman Страницы: 2

Бренд: GlammFire Страницы: 5

Бренд: Uniflame Страницы: 2

Бренд: Valor Страницы: 8

Бренд: Valor Страницы: 20

Бренд: Valor Страницы: 24

President ZC Cast Front 536CXB

Бренд: Valor Страницы: 18

Бренд: Valor Страницы: 8

Бренд: Valcourt Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды