Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

background image

20306743

17

KSTDV Series Gas Fireplace

VENTING INSTALLATION

Example:

Elbow 1   =   90°
Elbow 2   =   45°
Elbow 3   =   45°
Elbow 4   =   90°

Total Angular Variation = 270°

Figure 17 -
Maximum Elbow Usage

1

2

3

4

24" (610 mm)
Minimum

FP1383

supplied). Re

fi

ll hole with 12" of coarse gravel leaving

a clearance of approximately 4" below snorkel.

Figure

18

3. Install vent system.
4. Ensure a watertight seal is made around the vent pipe

coming through the wall.

5. Apply high temperature sealant caulking (supplied)

around the 5" and 8" snorkel collars.

6. Slide the snorkel into the vent pipes and secure to the

wall.

7. Level the soil so as to maintain a 4" clearance below

snorkel.

Figure 18

Figure 18 -
Below Grade Installation

Screws

Minimum
4" Clearance

Ground

Window
Well

Gravel

Drain

Foundation
Wall

Firestop

24"

(610 mm)

Minimum

•

For each 45° elbow installed in the horizontal run, the
length of the horizontal run MUST be reduced by 18"
(457 mm). This does not apply if the 45° elbows are
installed on the vertical part of the vent system.

•

The maximum number of elbow degrees in a system is
270°.

Figure 17

BELOW GRADE INSTALLATIONS

When it is not possible to meet the required vent terminal
clearances of 12" above grade level, a snorkel kit is rec-
ommended. It allows installation depth down to 7" (178
mm) below grade level. The 7" (178 mm) is measured
from the center of the horizontal vent pipe as it penetrates
through the wall.

Ensure that sidewall venting clearances are observed.
If venting system is installed below ground, we recom-
mend a window well with adequate and proper drainage
to be installed around the termination area.

If installing a snorkel, a minimum 24" vertical rise is neces-
sary. The maximum horizontal run with the 24” vertical pipe
is 36". This measurement is taken from the collar of the

fi

replace (or transition elbow) to the face of the exterior wall.

See the Sidewall Venting Graph for extended horizontal
run if the vertical exceeds 24".
1. Establish vent hole through the wall.
2. Remove soil to a depth of approximately 16" below base

of snorkel. Install drain pipe. Install window well (not

If the foundation is recessed, use recess brackets (not
supplied) for securing lower portion of the snorkel. Fasten
brackets to wall

fi

rst, then secure to snorkel with self drilling

#8 x 1/2 sheet metal screws. It will be necessary to extend
vent pipes out as far as the protruding wall face.

Figure 19

Figure 19 -
Snorkel Installation, Recessed Foundation

Foundation
Recess

Watertight Seal
Around Pipe

Sheet Metal
Screws

Wall Screws

Snorkel

For models purchased after 4/16/15, please see addendum.

«
...
15
16
17
18
19
...
»

Содержание KSTDV500(N/P)TSCSB









































































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренд: Majestic Страницы: 56

LEGEND G4 780IN (NG)

Бренд: Valor Страницы: 44

Бренд: Valor Страницы: 30

Бренд: Valor Страницы: 12

CHURCHILL 32-810-58

Бренд: Valor Страницы: 29

Бренд: Valor Страницы: 9

Бренд: Valor Страницы: 56

President ZC Cast Front 536CXB

Бренд: Valor Страницы: 18

Portrait 569 Ledge Front

Бренд: Valor Страницы: 18

Бренд: Valor Страницы: 39

Бренд: Valor Страницы: 4

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 78

Бренд: Valor Страницы: 58

Portrait Series

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 10

OXYSAFE CONTOUR 3290

Бренд: Valor Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды