Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 58

Страница: 58 / 72

20307393

5" x 8" DVP Termination Kit

IMPORTANT SAFETY INFORMATION

•

The termination cap MUST be vented directly to the

outside. The termination kit MUST NEVER be con

nected to a chimney flue(s) servicing a separate sol

id-fuel burning appliance or any other appliances.

•

Termination cap MUST NOT be recessed into a wall.

Figure 1

•

The flexible vent pipe cannot be intermingled with any

of the rigid vent pipe sections. DO NOT connect two

(2) sections of flexible vent pipe together to achieve a

longer length.

• The installation must conform with local codes or in

the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1 (in the United States) or with the

current installation code CSA B149 (in Canada).

•

These models are approved to use Hearth & Home

Technologies Direct Vent Pipe Components and Ver-

mont Castings Group termination kits. Refer to the

fireplace Homeowner’s Manual for approved venting

systems or components.

•

Horizontal runs must be supported every 3 feet (914

mm) using wall straps. Vertical runs must be supported

every 8 feet (2.4 m) using wall straps. Slip wall straps

loosely on to pipe. Attach straps to framing members

using nails or screws. Tighten nut/bolt to secure pipe.

•

The fireplace and venting system should be inspected

before initial use and at least annually by a qualified

field service person. Inspect the external vent cap on a

regular basis to make sure that no debris is interfering

with the airflow. Inspect entire venting system to en

sure proper function.

Figure 1 -

Termination Cap on Wall

Outside Wall

Finishing Material
(Vinyl Siding, etc.)

PRE-INSTALLATION INFORMATION

Before You Start

Plan your installation. Set the unit in place and survey how

to best vent the unit. Select the appropriate termination kit

and vent pipe for the installation. Read these instructions

and the fireplace Homeowner’s Manual before beginning

installation. After vent configuration has been decided,

begin attaching pipe to unit.
Items required for installation:

Tools:

Phillips screwdriver

Hammer

Saw and/or saber saw Level

Measuring Tape

Electric drill and bits

Pliers

Square

Building Supplies:

Framing materials

Wall finishing materials

Caulking Material (noncombustible)

WARNING

Any horizontal run must have a 1/4" rise for every one

(1) foot of run towards the vent termination. Never

allow the vent pipe to run down. This could cause high

temperatures and may present a fire hazard.

WARNING

Termination cap must be positioned so the embossed

arrow is pointed up.

WARNING

Refer to your fireplace Homeowner’s Manual for the

minimum and maximum venting requirements of your

fireplace and for approved horizontal vent termination

locations prior to installation. Failure to do so may cause

fire hazard.

Содержание KSTDV500(N/P)TSCSB









































































Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды

Vermont Castings KSTDV500(N/P)TSCSB, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды