Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 10

Страница: 10 / 72

20306743

KSTDV Series Gas Fireplace

FIREPLACE INSTALLATION

FINISHING MATERIAL

NOTE:

Any remote wiring (i.e. remote control, wall switch,

and optional fan) must be done prior to

nal

nishing to

avoid costly reconstruction.
Only noncombustible materials (i.e. brick, tile, slate, steel,
or other materials with a UL

re rating of Zero) may be

used to cover the black surface of the appliance. A 300°F
minimum adhesive may be used to attach facing materials
to the black surface. If joints between the

nished wall

and the

replace surround are sealed, a 300°F minimum

sealant material (General Electric RTV103 or equivalent)
must be used.

NOTE

Never install combustible materials over
front face of fi replace.

Figure 6 -
Secure Fireplace to Floor and Framing Studs

Nailing Flange

Screws

Framing

FP2545

Noncombustible
Material

SECURE FIREPLACE TO FLOOR OR FRAM-
ING

The

replace must be secured to the

oor and/or to framing

studs as shown in

Figure 6

. Use four (4) wood screws or

masonry/ concrete screws to secure

replace to the

oor.

Use four (4) screws to attach

replace to framing. The side

brackets or nailing

anges are designed to accommodate

two wall boards thicknesses, 1/2" or 5/8".

A 6" area above fireplace must be a
noncombustible material. Figure 6

NOTE

Содержание KSTDV500(N/P)TSCSB









































































Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды

Vermont Castings KSTDV500(N/P)TSCSB, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KSTDV500(N/P)TSCSB

Отзывы:

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренды по названию

Популярные бренды