Vermont Castings KSTDV500(N/P)TSCSB Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 72

background image

20306743

31

KSTDV Series Gas Fireplace

FINAL INSTALLATION

Slots (Qty: 4.

Two per side)

Slot

SAFETY BARRIER INSTALLATION
INSTRUCTIONS

DANGER

HOT GLASS

WILL

CAUSE BURNS

.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and shall

be installed for the protection of children and

other at risk individuals.

20306543

Tabs

(two per side)

Figure 45

Figure 46

1. Remove screen from packaging.
2. Align the four slots on the sides of the screen frame

(two top, two bottom)

Figure 45

with the correspond-

ing shoulder bolts on the

fi

rebox

Figure 46

.

3. Slide the screen down onto the shoulder bolts until it

fi

ts securely in place.

4. Repeat on other side.

NOTICE

: It is the responsibility of the installer to ensure

the barrier is af

fi

xed to the

fi

replace at the time of instal-

lation.

CERTIFIED

S

AFETY

B

ARRIER

NOTE:

A barrier designed to reduce the risk of burns

from the hot viewing glass is provided with this
appliance and shall be installed for the protection of
children and other at risk individuals. If the barrier
becomes damaged, the barrier shall be replaced with
the manufacturer's barrier for this appliance.* Any
safety screen, guard, or barrier removed for servicing
the appliance must be replaced prior to operating the
appliance.

* See parts list for model number.

WARNING: The safety screen barrier
must be installed after the glass front is
in place. It is NOT a replacement for the
glass and the unit must NOT be oper-
ated without the glass in place.

«
...
29
30
31
32
33
...
»

Содержание KSTDV500(N/P)TSCSB









































































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500(N/P)TSCSB

Бренд: Jøtul Страницы: 36

Бренд: Foremost Страницы: 14

Бренд: Camina Страницы: 48

Бренд: Kemlan Страницы: 23

Бренд: Hearth & Home Страницы: 2

Бренд: Hiland Страницы: 3

Бренд: HAMPTON BAY Страницы: 60

Бренд: Teamson Home Страницы: 16

Бренд: Empire Comfort Systems Страницы: 28

Бренд: Rinnai Страницы: 20

"Zero Clearance" ZDV1001

Бренд: Kingsman Страницы: 16

Wellington Surround

Бренд: Valor Fires Страницы: 8

Fireplace Glass Door

Бренд: pleasant hearth Страницы: 27

Patio Lights 23170

Бренд: Landmann Страницы: 4

Бренд: Desa Страницы: 36

Smithy CM140-062

Бренд: Charmate Страницы: 4

Superior Fireplaces F3412

Бренд: IHP Страницы: 32

Бренд: Nibe Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды