Vacon NX ACTIVE FRONT END II Скачать руководство пользователя | Manualshive

Страница: 40 / 94

background image

40

• Vacon

arfiff05 Standard AFE-II

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

7.

DESCRIPTION OF PARAMETERS

7.1

Basic parameters

2.1.1

Grid Nominal Voltage

[# V]

ID110

This parameter sets the incoming line voltage for the regenerative drive. The maximum
value is 690 V, Set this parameter to the nominal line voltage at the installation site.

2.1.2

Grid Nominal Frequency

[#,## Hz]

ID1532

Grid Nominal frequency. Used for frequency protection functions and initial guess for
synchronization frequency.

2.1.3

System Rated Current

[A]

ID113

Rated current capacity of the supply or the transformer. May need to be set if AFE is
oversized compared to LCL or feeding transformer capacity. For testing purposes, the
feeding transformer should not be less than 20% of the unit nominal current or following
breakers or fuses. Recommended not to increase System Rated Current above I

H

Current.

2.1.4

System Rated Power

[kW]

ID116

Set here the rated active power of the system.

2.1.5

Parallel AFE

ID1501

0 = Single AFE

1 = Parallel AFE

When selecting parallel, AFE DC Drooping is set to 4,00 %, Software Modulation 1 is
activated (Default Software Modulator 2) and modulation is automatically synchronized
between AFE units in common DC bus.

2 = Master

When selecting Master, AFE DC Drooping is set to 4,00 %, Software Modulation 1 is
activated (Default Software Modulator 2) and modulation is automatically synchronized
between AFE units in common DC bus. Start Command is send trough system bus to
follower drives

3 = Follower

When selecting follower, AFE DC Drooping is set to 4,00 %, Software Modulation 1 is
activated (Default Software Modulator 2) and modulation is automatically synchronized
between AFE units in common DC bus. Follower drive revives start command from
master drive through system bus.

«
...
38
39
40
41
42
...
»

Содержание NX ACTIVE FRONT END II































































































Отзывы:

Нет отзывов

Похожие инструкции для NX ACTIVE FRONT END II

Бренд: BADODOSECURITY Страницы: 8

Бренд: Yudian Страницы: 26

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 27

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 10

Бренд: iluminize Страницы: 2

Бренд: Ban Seok Страницы: 9

Бренд: M-system Страницы: 10

U-verse Advance Series A10

Бренд: AT&T Страницы: 2

Бренд: Goodson Страницы: 4

Бренд: Moeller Страницы: 2

Бренд: ITALCOPPIE SENSORI Страницы: 2

Бренд: R for Rabbit Страницы: 2

Бренд: Westfalia Страницы: 18

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды