Vacon NX ACTIVE FRONT END II Скачать руководство пользователя страница 18

Страница: 18 / 94

• Vacon

arfiff05 Standard AFE-II

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

5.1

Monitoring values

The monitoring values are the actual values of parameters and signals as well as statuses and
measurements. Monitoring values cannot be edited.

5.1.1

Monitoring 1

Code

Signal

Unit

Description

V1.1.1

DC-Link Voltage

Vdc

1108

Measured DC Link voltage in Volts, filtered.

V1.1.2

DC-Link Ref.

Vdc

DC Voltage Reference in Vdc

V1.1.3

DC Voltage Ref.

1200

Used DC Voltage Reference

V1.1.4

DC Voltage Act.

Actual DC Voltage

V1.1.5

Total Current

Total current of the regenerative unit in
Amperes.

V1.1.6

Active Current

1125

Avtive current of the regenerative drive in % of
Rated Line Current.
> 0 power from AC side to DC side
< 0 power from DC side to AC side

V1.1.7

Reactive Current

1157

Reactive current of the regenerative drive in % of
Rated Line Current.
> 0 Inductive current
< 0 Capacitive current

V1.1.8

Supply Frequency

Supply frequency in ##.## Hz .The sign indicates
the phase order.

V1.1.9

Supply Voltage

Input AC voltage, RMS line to line Volts.

V1.1.10

Unit Temperature

°C

Heat sing temperature

V1.1.11

Status Word

V1.1.12

DIN 645. 321

V1.1.13

Analogue Input 1

V1.1.14

Analogue Input 2

V1.1.15

Analogue Out 1

V1.1.16

Operation Hours

1856

5.1.2

FieldBus Monitoring values

Code

Signal

Unit

Description

V1.2.1

FB Control Word

1160

Control word from fieldbus

V1.2.2

FB Status Word

Status word to fieldbus

V1.2.3

Fault Word 1

1172

V1.2.4

Fault Word 2

1173

V1.2.5

DIN Status Word 1

V1.2.6

DIN Status Word 2

V1.2.7

Warning Word 1

1174

V1.2.8

DC Voltage

Unfiltered DC-Link voltage

V1.2.9

Current

1113

Unfiltered total current

V1.2.10

Drive Power

1508

Electrical AFE terminal power

V1.2.11

Fault History

V1.2.12

Final DC Ref

1131

V1.2.13

Cabin State Word

1884

5.1.3

Line Monitor OPT-D7

Code

Signal

Unit

Description

V1.3.1

Line Voltage

1650

V1.3.2

Line Frequency

1654

V1.3.3

Synch Error D7

1659

V1.3.4

Line Voltage THD

1670

V1.3.5

Line Voltage HF rms

1671

Содержание NX ACTIVE FRONT END II































































































Результаты поиска

Содержание NX ACTIVE FRONT END II

Отзывы:

Похожие инструкции для NX ACTIVE FRONT END II

Бренды по названию

Популярные бренды

Vacon NX ACTIVE FRONT END II, Руководство по применению

Результаты поиска

Содержание NX ACTIVE FRONT END II

Отзывы:

Похожие инструкции для NX ACTIVE FRONT END II

Бренды по названию

Популярные бренды