Vacon NX ACTIVE FRONT END II Скачать руководство пользователя | Manualshive

Страница: 11 / 94

background image

Arfiff05 Standard AFE-II

vacon •

11

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

3.

OPERATION

3.1

Charging of DC

This AFE application has own charging control, P2.4.1.9 DC Charge (24 Vdc required for control
board)

level

within set time P2.7.1.5 Charge Max Time (provided that DC Voltage reach at least drive under
voltage fault level).

Charging function is activated when P2.4.1.9 DC Charge is A.1 or higher. When control place is IO,
Keypad or NCDrive charging is started from start command.
Charging is not started if:

-

Drive is in fault state.

-

P2.3.1.2 Enable MCB Close is FALSE

-

P2.3.1.6 Run Enable is FALSE

-

P2.3.1.7 Quick Stop is FALSE

Charging is also stopped if above conditions happens during charging or start command is removed.

For  fieldbus  control  charging  is  started  with  B0  of  FB  Control  Word  on  supporting  FB  profiles.
Charging is also stopped if B0 goes low as is MCB opened if already closed.

DC Charge (F80) is given if 85 % of DC Nominal is not reached within P2.7.1.5 Charge Max Time and
charging is stopped.

DC Charging is stopped when drive receives feedback from P2.3.1.5 MCB Status.

Note! Use suitably sized DC Charging resistor by checking Pulse loadability for time duration set in
for Max Charge Time parameter

3.2

Main Circuit breaker control (MCB control)

The AFE application controls the MCB of the system with Relay Output RO2. When charging of the DC
bus is ready the  MCB will be closed. The status of the  MCB is monitored via digital input  P2.3.1.5
MCB Status (Default is DigIn: A.4). MCB feedback is required for correct AFE functionality,

NOTE! MCB feedback is required for correct AFE functionality.

Over Current (F1), Hardware IGBT (F31) and Software IGBT (F41) faults will open  MCB immediately.
Some fault can be programmed to open MCB if needed.

NOTE! For correct operation of AFE system, AFE unit needs to be in control of charging circuit and
Main Circuit Breaker (MCB).

«
...
9
10
11
12
13
...
»

Содержание NX ACTIVE FRONT END II































































































Отзывы:

Нет отзывов

Похожие инструкции для NX ACTIVE FRONT END II

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Garmin Страницы: 4

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: Centurion Страницы: 16

Бренд: K&K Страницы: 10

Бренд: Vertiv Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды