Vacon NX ACTIVE FRONT END II Скачать руководство пользователя

Страница: 87 / 94

Arfiff05 Standard AFE-II

vacon •

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

F31

IGBT temperature

IGBT Inverter Bridge over temperature protection has detected too high a short term overload
current.
Possible cause:
1.

Too high load

Identification run has not been made which causes the motor to start under magnetized.

Correcting measures:
1.

Check load.

Check motor size.

Make identification Run.

F32

Fan cooling

Possible cause:
1.

Cooling fan of the frequency converter does not start when ON command is given.

Correcting measures:
1.

Contact your local distributor.

F37

Device change

Option board or power unit changed.

Possible cause:
1.

New device of same type and rating.

Correcting measures:
1.

Reset. Device is ready for use.

F38

Device added

Option board added.

Correcting measures:
1.

Reset. Device is ready for use. Old board settings will be used.

F39

Device removed

Option board removed.

Correcting measures:
1.

Reset. Device no longer available.

F40

Device unknown

Unknown option board or drive.

S1 = Unknown device
S2 = Power1 not same type as Power2

Correcting measures:
1.

Contact the distributor near to you.

Содержание NX ACTIVE FRONT END II































































































Результаты поиска

Содержание NX ACTIVE FRONT END II

Отзывы:

Похожие инструкции для NX ACTIVE FRONT END II

Бренды по названию

Популярные бренды

Vacon NX ACTIVE FRONT END II, Руководство по применению

Результаты поиска

Содержание NX ACTIVE FRONT END II

Отзывы:

Похожие инструкции для NX ACTIVE FRONT END II

Бренды по названию

Популярные бренды