U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 53 / 96

prepurge the motor and igniter will operate but the

oil valve will remain closed. Refer to Oil Primary

Control Instructions for more details.

4. Adjust oil pressure.

a. When checking a fuel unit's operating pressure, a

reliable pressure gauge may be installed in either

the bleeder port or the nozzle port. For Beckett

and Carlin burners refer to Figure 28. Refer to

Figure 7E for Riello burner.

b. Locate oil pressure adjusting screw and turn

screw to obtain proper pump pressure, refer to

Table 12 at the rear of this manual.

c. To check the cutoff pressure, deadhead a reliable

pressure gauge onto the copper connector tube

attached to the nozzle port. Run the burner for

a short period of time. Shut the burner off. The

pressure should drop and hold.

d. Remove the gauge and install bleeder port and/or

reconnect the nozzle port line.

SECTION XI: SYSTEM START-UP (continued)

Figure 28: Adjusting Fuel Pump Pressure

ADJUST OIL BURNER WHILE OPERATING.

(flame present)
1. SET ROOM THERMOSTAT about 10°F below

room temperature.

2. PRESS RED RESET BUTTON on Oil Primary

Control and release.

3. READJUST THE HEAD SETTING only if

necessary.

Beckett Burners

a. V8H3:
Beckett MB(L1) Head burners have a fixed head

which are non-adjustable.

b. V8H4 thru V8H9:

Beckett MD(V1) (variable) Head burners have

the ability to control air by moving the head. It

might be necessary to move the head forward

or back one position at a time to optimize the

smoke and CO

readings. See Figure 29A.

Carlin Elite EZ Burners

a. Carlin EZ-1HP and EZ-2HP burners use a head

positioning bar to fix the head setting based

on nozzle size. To adjust this setting, bar must

be changed to the next larger or smaller bar

available. Refer to Section III, Paragraph K, 7b

for details.

Carlin 102CRD Burners

a. V8H7 through V8H9
The Carlin 102 CRD-3 Burner has the ability

to control air by moving the head. It might be

necessary to move the head forward or back one

position at a time to optimize the smoke and

CO2 readings.

b. If the fire is a little too rich, move the

combustion head slightly forward by increasing

dimension “A”. Refer to Figure 7A.

4. READJUST THE TURBULATOR SETTING only

if necessary.

Riello Burners

a. V8H3 through V8H9
Move the turbulator setting forward or back one

position at a time to optimize the smoke and

CO2 readings. Refer to Figure 7D and Table 12

at the rear of this manual.

5. ADJUST DRAFT REGULATOR for a draft of

-0.02" (water gauge) over the fire after chimney has

reached operating temperature and while burner is

running.

6. READJUST THE AIR DAMPER SETTING (Air

Band, Air Shutter or Air Gate) on the burner for

a light orange colored flame while the draft over

the fire is -0.02”. Use a smoke tester and adjust

air for minimum smoke (not to exceed #1) with a

minimum of excess air. Make final check using

suitable instrumentation to obtain a CO

of 11.5

to 12.5% with draft of -0.02” (water gauge) in fire

box. These settings will assure a safe and efficient

operating condition. If the flame appears stringy

instead of a solid fire, try another nozzle of the same

type. Flame should be solid and compact. After all

adjustments are made recheck for a draft of -0.02”

over the fire.

7. ONLY READJUST THE

HEAD

TURBULATOR

SETTING

if necessary.

a. V8H3 through V8H9
Move the setting

forward or back one position at

a time to optimize the smoke and CO

readings.

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды