U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 22 / 96

5. Install float-type LWCO, if so equipped.
See Figures 5 and 9.

a. Install nipples and unions in "D" Tappings.
b. Mount hardware to low water cut-off body.

Install assembly.

c. Install water gage glass on low water cut-off

assembly's tee fittings.

6. Install Pressure Limit Control.

Float LWCO only: Remove ¼" NPT plug from

top of Low Water Cut-Off. Install Syphon and

Limit into this tapping. See Figure 9.

b. Probe LWCO only: Install Limit in Tapping "A"

using ¾" NPT x 3" long nipple, ¾" NPT elbow,

¾" NPT x ¼" NPT bushing, and syphon. See

Figures 5 and 10.

DO NOT

tighten the limit by holding the case;

apply a wrench to the brass hex below the case.

d. An L404F pressure limit does not require

leveling.

7. Connect the field wiring to the LWCO or the

R8239A Control Center/J-box, or burner disconnect

J-box.

a. If equipped with tankless heater, connect field

wiring from the aquastat control to the R8239A

Control Center transformer terminals or oil

burner primary control's "T-T" terminals.

Make the wiring connections as shown in

appropriate wiring diagram, refer to Figure 22,

23A, 23B, 24A or 24B.

Note: DO NOT

remove "T-T" jumper unless

wiring diagram indicates a direct connection

from thermostat and/or tankless heater aquastat

control to the oil burner primary control's "T-T"

terminals.

Also refer to Section XI, Paragraph I, Item 2,

"Verify Oil Primary Control" for more details.

b. Refer to Paragraph R for details on use of

burner disconnect junction box provided with all

knockdown boiler builds.

P. INSTALL TRIM AND CONTROLS WITH

CARLIN BURNERS.

Water boilers Only

(see Figures 1A, 1B, 1C and 5).

Follow instructions in Paragraph N, Steps 1 through 7.

Steam Boilers Only

(see Figures 1D and 5).

Follow instructions in Paragraph O, Steps 1 through 6.
7. Connect Field Wiring

a. Steam Boiler with Hydrolevel CG450 LWCO,

Carlin Burner.

Connect the field wiring to the R8239A Control

Center. If equipped with tankless heater, connect

field wiring from the aquastat control to the

R8239A Control Center’s “R-G” terminals.

Make the wiring connections as shown in

Figure 22.

b. Steam Boiler with McDonnell & Miller

PS-801 or McDonnell & Miller 67 LWCO,

Carlin Burner.

Connect the field wiring to the LWCO or the

burner disconnect J-box. If equipped with

tankless heater, connect field wiring from

the aquastat control to the oil burner primary

control’s “T-T” Terminals. Make the wiring

connections as shown in appropriate wiring

diagram, refer to Figure 23A, 23B, 24A or 24B.

Note: DO NOT

remove "T-T" jumper unless

wiring diagram indicates a direct connection

from thermostat and/or tankless heater aquastat

control to the oil burner primary control's "T-T"

terminals.

Also refer to Section XI, Paragraph I, Item 2,

"Verify Oil Primary Control" for more details.

SECTION III: KNOCKDOWN BOILER ASSEMBLY (continued)

Figure 9: Float-Type Low Water Cut-Off and

Pressure Limit Installation

Figure 10: Pressure Limit Installation for Probe

LWCO Equipped Boilers

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды