U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 58 / 96

Figure 31: Cad Cell Location

•

Close line switch to boiler. If burner starts

and runs beyond safety switch cut-off

time, cell is good. If not, install new cell.

•

Close hand valve in oil supply line.

•

Failure occurs, device enters Recycle Mode.

•

Device tries to restart system after

approximately 60 seconds.

•

After third Recycle Mode trial, safety

switch locks out within safety switch

timing indicated on label and control

enters Restricted Mode. Ignition and

motor stop and oil valves closes.

iv.

Power Failure Check: After Flame is

established, turn the power off to the control/

burner. The burner should shut down safely.

When power is restored a normal ignition

sequence should be started.

WARNING

Cad Cell Jumper must be removed after this

check.

SECTION XI: SYSTEM START-UP (continued)

3. CHECK HIGH LIMIT

a. Adjust system thermostat(s) to highest setting.
b. Allow burner to run until boiler water

temperature exceeds high limit setting. The

burner should shut down and circulators continue

running.

c. Allow the temperature to drop below control

setting. The burner must restart.

d. Boiler installation is not considered complete

until this check has been made.

e. Check low water cut-off control with water level

at normal water line (see Figure 1D). Raise

thermostat setting to allow burner to operate.

Open boiler drain to allow water level to drop

to bottom of sight glass until burner operation is

shut-down by low water cut-off.

Close boiler drain and refill to normal water line.

Burner should automatically restart during fill.

Lower thermostat setting.

f. Check operating control on boiler applications

equipped with tankless heater(s). With burner

off, draw hot water until burner starts, then turn

off hot water and check burner shut-down.

J. IF CONTROLS MEET REQUIREMENT

outlined

in Paragraph I.
1. Allow boiler to operate for approximately 30

minute, confirm the boiler and system have no leaks.

IF CONTROLS DO NOT MEET

REQUIREMENTS

outlined in Paragraphs I-1 thru

I-6, replace control and repeat checkout procedures.

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды