U.S. Boiler Company V8H SERIES Скачать руководство пользователя страница 51

Страница: 51 / 96

SECTION XI: SYSTEM START-UP

e. Open purge valve.
f. Open shut-off valve in cold water supply piping

located between the air scoop and expansion

tank.

g. Allow water to overflow from bucket until

discharge from hose is bubble free for 30

seconds.

h. When zone is completely purged of air, close

zone valve or shut-off valve. Open zone valve to

the next zone to be purged. Repeat this step until

all zones have been purged. At completion, open

all zone valves.

i. Close purge valve, continue filling the system

until the pressure gauge reads 12 psi. Close shut-

off valve in cold water supply piping.

WARNING

The maximum operating pressure of this boiler

is posted on the ASME Data Label located on the

top of the boiler. Never exceed this pressure. DO

NOT plug safety or relief valve.

NOTICE

If make-up water line is equipped with pressure

reducing valve, system will automatically fill to 12

psi. Follow fill valve manufacturer's instructions.

j.  Open full port ball valve in boiler system piping.
k.  Remove hose from purge valve.
l.  Confirm that the boiler and system have no water

leaks.

CHECK CONTROLS, WIRING AND

BURNER

to be sure that all connections are tight and

burner is rigid, that all electrical connections have been

completed and fuses installed, and that oil tank is filled

and oil lines have been tested.

ADJUST CONTROL SETTINGS

with burner

service switch turned “ON”.
1. SET ROOM THERMOSTAT about 10°F below

room temperature.

2. PRESS RED RESET BUTTON on front of

burner cover (Beckett, Riello burners) or Primary

Control (Carlin Burner), hold button for one (1)

second and release to reset primary control.

ALWAYS INSPECT INSTALLATION

BEFORE STARTING BURNER.

1. Verify that the venting, water piping, oil piping, and

electrical system are installed properly. Refer to

Installation Instructions contained in this manual.

2. Confirm all electrical, water and oil supplies are

turned off at the source and that the vent is clear

from obstructions.

WARNING

Completely read, understand and follow all

instructions in this manual before attempting

start up.

FILL HEATING SYSTEM WITH WATER.

NOTICE

It is important, especially in a steam system, to

properly remove the oil and dirt from the system.

Failure to clean the system can result in erratic

water lines and surging.

CLEAN HEATING SYSTEM if boiler water or

condensate return water is dirty or if erratic water lines

or surging exist after a few days of boiler operation.

Refer to Maintenance and Service Instructions Section

of this manual for proper cleaning instructions for

steam and water boilers.
1. STEAM BOILERS — Fill boiler to normal water

line. Refer to Figure 1D.

2. HOT WATER BOILERS. Fill entire heating

system with water and vent air from system. Use

the following procedure on a series loop or multi-

zoned system installed as per Figures 15A and 15B,

to remove air from system when filling:

a. Close full port ball valve in boiler system piping.
b. Isolate all zones by closing zone valves or shut-

off valves in supply and return of each zone(s).

c. Attach a hose to vertical purge valve in boiler

system piping.

(

Note

- Terminate hose in five gallon bucket at a

suitable floor drain or outdoor area).

d. Starting with one zone at a time, open zone valve

or shut-off valve in boiler supply and return

piping.

WARNING

All boilers equipped with burner swing door have a potential hazard which can cause severe property damage,

personal injury or loss of life if ignored. Before opening swing door, turn off service switch to boiler to

prevent accidental firing of burner outside the combustion chamber. Be sure to tighten swing door fastener

completely when service is completed.

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды