U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 52 / 96

3. STEAM BOILERS:
With an L404F Pressure Limit - set cut-out

pressure (MAIN scale) on the pressure limit for

(1) PSI and differential pressure (DIFF.) for .5 PSI.

These pressures may be varied to suit individual

requirements of the system.

4. STEAM BOILERS WITH TANKLESS

DOMESTIC WATER HEATERS, set boiler

water temperature dial on L4006 operating control

at 190°F (max.). Set differential at 10°.

5. WATER BOILERS WITHOUT TANKLESS

HEATERS are equipped with an Intelligent Oil

Boiler Control (Boiler Control). The Boiler Control

is factory programmed with a High Limit setpoint

of 180 F. The High Limit setpoint is adjustable

between 140 F and 240 F. This temperature may be

varied to suit the installation requirements

6. WATER BOILERS WITH TANKLESS HEATERS

are equipped with a Warm Start Intelligent Oil

Boiler Control (Warm Start Boiler Control). The

Warm Start Boiler Control is factory programmed

with a High Limit setpoint of 180 F. The High

Limit setpoint is adjustable between 140 F and 240

F. Additionally, the Warm Start Boiler Control is

factory programmed with a Low Limit setpoint

of 110 F. The Low Limit setpoint is adjustable

between 110 F and 220 F. These temperatures may

be varied to suit the installation requirements.

7. CHECKOUT
Put the system into operation and observe at least

one complete cycle to make sure that the controller

operates properly. See Troubleshooting Section to

use LED to assist in determining system operation.

ADJUST OIL BURNER BEFORE STARTING.

1. CHECK BURNER SETTINGS and readjust if

necessary, see Burner Specifications, Table 12 at the

rear of this manual.

Beckett Burners

a. Inspect Beckett head setting on left side of

burner housing by insuring the blue line MD(V1)

or the line on the label MB(L1) are aligned,

readjust if necessary. Refer to Figure 29A and

Table 12 at the rear of this manual.

b. Check burner air band and air shutter settings.

Readjust if necessary, see Table 12 at the rear of

this manual.

c. OPEN ALL OIL LINE VALVES.
d. Attach a plastic hose to fuel pump vent fitting

and provide a pan to catch the oil.

e. OPEN FLAME OBSERVATION PORT

COVER on burner swing door.

Carlin Elite EZ Burners

a. Inspect Carlin head setting on left side of burner

to ensure that the proper head positioning bar

matches the nozzle that is installed in drawer

assembly. Refer to Section III, Paragraph K,

Step 7b and Table 12 at the rear of this manual.

Replace bar if necessary.

b. Check air band settings. Readjust if necessary,

see Table 12 at the rear of this manual.

c. OPEN ALL OIL LINE VALVES.
d. Attach a plastic hose to fuel pump vent fitting

and provide a pan to catch the oil.

e. OPEN FLAME OBSERVATION PORT

COVER on burner swing door.

Carlin 102CRD Burners

a. Inspect Carlin head setting on left side of burner

by reading the scale embossed on the housing.

Refer to Figure 7A and Table 12 at the rear of

this manual.

b. Check air band settings. Readjust if necessary,

see Table 12 at the rear of this manual.

c. OPEN ALL OIL LINE VALVES.
d. Attach a plastic hose to fuel pump vent fitting

and provide a pan to catch the oil.

e. OPEN FLAME OBSERVATION PORT COVER

on burner swing door.

Riello Burners

a. Inspect Riello head setting on left side of burner

by reading the scale embossed on the housing

cover. Refer to Figure 7D and Table 12 at the

rear of this manual.

b. Inspect Riello burner air damper and turbulator

setting. Readjust if necessary, see Table 12 at the

rear of this manual.

c.  OPEN ALL OIL LINE VALVES.
d.  Provide a pan to catch oil.
e.  Remove pressure port/bleeder plug from fuel

pump and install Riello Combination Pressure

Gauge and Bleeder Valve Assembly.

f. OPEN FLAME OBSERVATION PORT COVER

on burner swing door.

START OIL BURNER.

1. Open vent fitting on fuel pump.
2. TURN ‘ON’ BURNER service switch and

allow burner to run until oil flows from vent

fitting in a SOLID stream without air bubbles for

approximately 10 seconds.

3. Close vent fitting and burner flame should start

immediately after prepurge is completed. Prepurge

prevents burner flame until 10 seconds has elapsed

after initial power is applied to burner. During

SECTION XI: SYSTEM START-UP (continued)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды