U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 14 / 96

Figure 6: Knockdown Boiler Jacket Assembly

INSTALL TRIM.

The following steam or water trim

will be concealed or inaccessible after boiler jacket is

installed, see Figure 5 for boiler tapping locations and

usage.
1.

STEAM BOILER — Top tappings:
a. Tapping "L" — Install 2" NPT plug in rear

section top supply tapping on boiler sizes V8H3

thru V8H5, if only one supply riser is used.

b. Tapping “M” — Install ¾” NPT coupling and

¾” NPT x 8” long nipple into ¾” NPT tapping

located next to front section top supply tapping

— all boiler sizes.

WATER BOILER — Top tappings:
a. Tapping “L” — Install 2” NPT plug in rear

section top supply tapping — all boiler sizes.

b. Tapping “M” —Install ¾” NPT x 8” long nipple

into ¾” NPT tapping located next to front section

top supply tapping — all boiler sizes.

INSTALL BOILER JACKET.

(See Figure 6).

1. Remove burner swing door and hinge assembly.

Remove one (1) 5/16"-18 flange nut and washer

from right side latching stud and one (1) 5/16"-

18 x 3½" cap screw on left side used for securing

burner swing door to the boiler section. Swing

door open and remove 5/16" hairpin cotter from

rear hinge pin (see Figure 7). While holding swing

door remove hinge pin and set door aside. Remove

two (2) 5/16"-18 x ¾" long cap screws securing the

hinge bracket to the boiler section.

2. Install jacket rear panel support bracket. (See

Figure 6, Item 2A). Align bracket with two (2)

5/16"-18 tapped holes in rear section and secure

with two (2) 5/16"-18 x 1/2" long cap screws.

3. Install jacket rear panel. (See Figure 6, Item 2B).

Align holes in jacket rear panel and support bracket.

Secure with two (2) #8 x 1/2" long sheet metal

screws.

4. Jacket Front Panel

a. Install black plastic collar extension to jacket

front panels for 7-13/16" diameter tankless

heater opening. (See Figure 6, Items 2C and

2D). Engage two (2) of the collar retaining

tabs over raw edge of jacket opening. Provide

support behind the panel with one hand while

applying pressure on collar to snap each tab

over edge of opening until all eight (8) tabs are

securing collar.

b. Install jacket front panel. Locate two (2) 11/32"

diameter holes, one round, one obround, on front

panel approximately 16” up from the bottom of

the panel. Align these holes with the similarly

located 5/16"-18 tappings on the front section.

Secure with two (2) 5/16"-18 x 1/2" long cap

screws.

5. Install jacket left side panel. (See Figure 6, Item

2E). Fold panel at perforation keeping insulation

inward. Align left side panel mounting holes with

the front and rear panel holes. Secure with #8 x ½”

long sheet metal screws.

SECTION III: KNOCKDOWN BOILER ASSEMBLY (continued)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды