U.S. Boiler Company V8H SERIES Скачать руководство пользователя страница 12

Страница: 12 / 96

SECTION III: KNOCKDOWN BOILER ASSEMBLY

REMOVAL OF BARE BOILER FROM SKID

1. Boiler is secured to skid with 4 bolts, 2 in front and

2 in rear of shipping skid, see Figure 3. Remove all

bolts.

Figure 3: Knockdown Boiler Removal from Skid

2. Tilt boiler to right and to rear. Using right rear leg

as pivot, rotate boiler 90° in a clockwise direction,

and lower left side of boiler to floor. Tilt boiler and

remove skid.

MOVE BOILER TO PERMANENT POSITION

by sliding or walking.

TEST BOILER FOR LEAKS

before installing

controls, trim, and jacket, and before connecting to

heating system.

1. Loosen nuts on tie rods until only finger tight.
2. Install pressure gauge (at least 50 PSI capacity),

a hose to the city water and a valve in the supply

tapping. Plug remainder of tappings.

3. Fill boiler with water and apply a pressure of at least

10 PSI but no more than 50 PSI gauge pressure.

WARNING

Assure that there is not air left inside boiler when

checking for leaks. DO NOT test for leaks with

pressurized air.

4. Examine boiler carefully inside and outside for leaks

or damage due to shipment or handling.

DRAIN WATER FROM BOILER.

Remove gauge,

valve and plugs from those tappings to be used. Leave

other tappings plugged or bushed according to Figure 5.

INSPECT JOINTS BETWEEN SECTIONS.

All

joints are factory sealed. If there are any spaces due to

shipment or handling, seal them with boiler putty.

INSPECT FLUE COVER PLATES

for tightness.

If loose, retighten mounting hardware. If flue plate or

sealing rope is damaged, repair or replace as needed.

INSTALL AND SECURE CANOPY

with gasket

and hardware provided to ensure gas tight seal — see

Figure 4.

Figure 4: Boiler Canopy Installation

1. Cut two (2) strips 13 ¾” long from the roll of gasket

insulation. Place one (1) strip across the top of the

front section and the other across the rear section as

shown in Figure 4.

2. Cut the remainder of the roll into two (2) equal

pieces. Place each piece along the sides, allowing

the ends to overlap the front and rear pieces.

CAUTION

DO NOT

allow any flueway blockage by gasket.

3. Position canopy body within the retaining bar which

borders the flueway openings on top of the bare

boiler block assembly.

NOTICE

Jacket support bracket must be facing left side of

boiler - see Figure 4. Jacket will not fit if bracket

is not oriented correctly.

4. Secure canopy to boiler with two (2) 1/4" - 20 x 3"

long carriage bolts, 1/4" flat washers and 1/4" - 20

wing nuts provided.

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды