U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 89 / 96

APPENDIX A - LOW WATER CUT OFF (LWCO)

Wiring of Typical LWCO

When

A low water cutoff is required to protect a hot water

boiler when any connected heat distributor (radiation)

is installed below the top of the hot water boiler (i.e.

baseboard on the same floor level as the boiler). In

addition, some jurisdictions require the use of a LWCO

with a hot water boiler.

Where

The universal location for a LWCO on oil hot water

boilers is above the boiler, in either the supply or return

piping. The minimum safe water level of a water boiler

is at the uppermost top of the boiler; that is, it must be

full of water to operate safely.

It is recommended that the LWCO control is installed

above the boiler to provide the highest level of

protection. However, where the LWCO control is

approved by the LWCO control manufacturer for

installation in a high boiler tapping of a water boiler,

the use of the listed LWCO control is permitted when

it is installed according to the LWCO manufacturer's

instructions.

What Kind

Typically, in residential applications, a probe type

LWCO is used instead of a float type, due to their

relative costs and the simplicity of piping for a probe

LWCO.

How to Pipe

A “tee” is commonly used to connect the probe LWCO

in the supply or return piping, as shown below.

LWCO Location

Select the appropriate size tee using the LWCO

manufacturer’s instructions. Often, the branch
connection must have a

minimum

diameter to

prevent bridging between the probe and the tee. Also,

the run of the tee must have a minimum diameter to

prevent the end of the probe from touching or being

located too close to the inside wall of the run of the tee.

Ideally, manual shutoff valves should be located

above the LWCO and the boiler to allow for servicing.

This will allow probe removal for inspection without

draining the heating system. Many probe LWCO

manufacturers recommend an annual inspection of the

probe.

How to Wire

LWCO’s are available in either 120 VAC or 24 VAC

configurations. The 120 VAC configuration must be

applied to oil boilers by wiring it in the line voltage

service to the boiler (after the service switch, if so

equipped).

The presence of water in a properly installed LWCO

will cause the normally open contact of the LWCO to

close, thus providing continuity of the 120 VAC service

to the boiler.

It is recommended to supply power to the probe LWCO

with the same line voltage servicing the boiler as shown

below.

WARNING

DO NOT ATTEMPT to cut factory wires to install an aftermarket Low Water Cut Off (LWCO). Only use

connections specifically identified for Low Water Cut Off.

In all cases, follow the Low Water Cut Off (LWCO) manufacturer's instructions.

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды