U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 73 / 96

SECTION XV: TROUBLESHOOTING (continued)

b. If the Boiler Control detects an error it will flash "

Err

" (boiler control error) followed by a number. Use this text and

number to identify the boiler problem and corrective action in Table 11 below.

Display

Status

Recommended Corrective Actions

Err 

Temperature Sensor Fault

Temperature sensor failure, wire harness loose or shorted connection or control

hardware failure:

- Check sensor is securely attached to boiler control

- Check that sensor wire is not damaged

- If secure and in good condition, replace sensor

- If problem persists, replace control

Err 2

Communication Fault

Enviracom terminal is shorted to ground or line voltage.

- Check wiring to EnviraCOM terminals 1,2 and 3. Wiring to external EnviraCom

device is incorrect.

Err 3

Internal Hardware Fault

Error detected with AC power supply frequency or boiler control failure. Cycle power to

the control. Replace control if problem persists.

Err 4

Burner Output (B1) Fault

B1 output sensed powered during safety output relay check sequence or un-powered

during running, or powered in idle in combination with water temperature above 264°F

limit. Cycle power to the control. Replace control if problem persists.

Err 5

Line Voltage Fault (< 80 Vac)

AC voltage out of specification high or low; check L1, L2, 110 VAC.

Err 6

Fuse missing

Internal fuse is blown or missing. The fuse protects the Aquastat from miswiring the L1

and L2 on Oil Primary. When the Oil Primary is correctly wired the fuse is useless and

not detected. If Primary is wired incorrectly the fuse is blown out and Aquastat report

error 6. EnviraCOM message is sent when the wiring is fixed and the error disappears

to indicate the end of the error state. Check wiring and replace fuse.

Err 

User settings lost, (reset to

factory defaults)

Warning: Generated if user adjustments are lost and the device uses factory default

values. Error is cleared by entering and exiting the Adjustment mode. Replace control

if problem persists.

Err 

Manual Reset Lockout

(resettable)

Set if

Err 4

was invoked four times in a row. Check wiring and clear Lockout by

pressing all three user keys for 30 seconds.

TABLE 11: BOILER CONTROL ERROR NUMBERS

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды