U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 75 / 96

Item

No. Description

Part No. V8H3 V8H4 V8H5 V8H6 V8H7 V8H8 V8H9

1. BARE BOILER ASSEMBLy

Front Section (Non-Htr.), Machined Water

---(OR)---

Front Section (Non-Htr.), Machined Steam

71728103

71728104

Front Heater Section, Machined Water

---(OR)---

Front Heater Section, Machined Steam

71728101

71728102

Center Section

71728201

Back Section (Non-Htr.), Machined Water

---(OR)---

Back Section (Non-Htr.), Machined Steam

---(OR)---

Heater Back Section, Machined Steam/Water

71728302

71728303

71728301

5" Cast Iron Slip Nipple

7066003

Slip Nipple, 22-B Steel

806600375

Tie Rod, 3/8"-16 x 12½" Lg.

80861010

---

Tie Rod, 3/8"-16 x 17¾" Lg.

80861032

---

Tie Rod, 3/8"-16 x 23" Lg.

80861049

---

Tie Rod, 3/8"-16 x 27½" Lg.

80861014

---

Tie Rod, 3/8"-16 x 32¾" Lg.

80861035

---

Tie Rod, 3/8"-16 x 37¾" Lg.

80861105

---

Tie Rod, 3/8"-16 x 42¾" Lg.

80861106

---

3/8" Flat Washer

80860600

3/8" -16 Hex Nut

80860423

Heater Cover Plate Gasket - Front Heater

8036068

Heater Cover Plate Gasket - Rear Heater

8036058

Blank Heater Cover Plate (WN) - Front Heater

7036002

Tapped Heater Cover Plate (WF[L]) - Front Heater

7036001

Blank Heater Cover Plate (UR & WR) - Rear Heater

7036020

Tapped Heater Cover Plate (WR[L]) - Rear Heater

7036021

222A Heater Carton Assy. - (WF[T]) - Front Heater

---(OR)---

A54 Heater Carton Assy. - (WF[T]) - Front Heater

6036036

6031204

---

V1-2 Heater Carton Assy. - (UR[T] & WR[T]) -

Rear Heater

6036031

5/16" Flat Washer

Front Heater

80860611

Rear Heater

3/8" -16 x 7/8" Lg. Plated Cap

Screw, ASME Grade SA307B

Front Heater

80861337

Rear Heater

Rear Target Wall Insulation

8202701

SECTION XVI: REPAIR PARTS (continued)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды