U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 21 / 96

6. After control is installed and secured, remove

control cover. Then, remove knockout located

directly above factory connected limit harness on

right side flange of control. Insert circulator harness

end with attached fork terminals thru knockout hole

and push-in to engage harness connector into flange.

Connect wires to control terminals as follows - Blue

to C1 and White to C2 and tighten securely. Re-

install control cover.

7. Connect Field Wiring.

Water boilers without tankless heater. Connect

the field wiring to the aquastat control. Make the

wiring connections as shown on Figure 21A.

b. Water boilers with front or rear tankless heater.

Connect the field wiring to the aquastat control.

Make the wiring connections as shown on Figure

21B.

c. Refer to Paragraph R for details on use of

burner disconnect junction box provided with all

knockdown boiler builds.

INSTALL TRIM AND CONTROLS WITH

BECKETT BURNER.

Steam Boiler Only

(see Figures 1D & 5).
1. Thread the pressure gauge into the ¼” NPT tapping

"B", of the front section. Tighten with wrench

applied to the square shank of the gauge.

CAUTION

DO NOT apply pressure to the gauge case - this

may result in inaccurate readings.

2. Thread 1½” NPT x ¾” NPT bushing and a ¾” NPT

drain valve into the 1½” NPT tapping located in the

lower right corner of the front section. Tighten with

wrench.

NOTICE

Lower rear section Tapping "H" is used for

standard condensate return on steam boilers.

3. Thread safety valve, as shown in Figure 1D, into ¾"

NPT coupling and ¾” NPT x 8” nipple previously

installed in Paragraph H, No. 1, step b. Tighten

with wrench. Pipe discharge as shown in Figure

16. Installation of the safety (relief) valve must be

consistent with ANSI/ASME Boiler and Pressure

Vessel Code, Section IV.

WARNING

Safety valve discharge piping must be piped near

floor to eliminate potential of severe burns.

NOT pipe in any area where freezing could occur.

DO NOT install any shut-off valves, plugs or caps.

4. Install probe type Low Water Cut-Off (LWCO) if so

equipped.
a. Thread probe into ¾” NPT tapping "C" located

on the front section, down and to the right of

the pressure gauge. Slip the low water cut-off

(LWCO) control over the probe and clamp in

place. Connect the wire(s) between the probe and

control per the manufacturer’s instructions.

WARNING

Read the manufacturer's instructions packed with

the probe LWCO for proper pipe dope application.

DO NOT

use Teflon tape on probe threads. Use of

teflon can render the probe LWCO inoperational.

b. Install the gauge glass using the two ½” NPT

tappings to the right of the probe LWCO.

SECTION III: KNOCKDOWN BOILER ASSEMBLY (continued)

Figure 8: Limit Sensor Insertion

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды