U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 25 / 96

Step 4.

From this position the door can be swung

clear of the vertical circulator return piping to

provide full access to the combustion chamber

and burner head (see Figure 13B, Position 3).

2. Perform routine inspection, service or cleaning as

necessary.

3. To close Burner Swing Door (see Figures 13A

and 13B):

Step 1.

From the fully open position, rotate Burner

Swing Door toward the closed position. Make

sure that the articulated hinge is rotated to the

extreme left position to allow the door to clear

the vertical circulator return piping as shown in

Figure 13B, Position 2.

Step 2.

Grasp the door's left side hinge flange

in your left hand and place your right hand

under the burner air tube to lift upward. Lift

the door up unto the built-in cast ramp/door

rest (protruding from the bottom of the front

section casting - see Figure 13A), while rotating

the articulated hinge and door to the right and

engaging the slot (on right side of door) unto the

5/16" stud protruding from the front section.

Step 3.

Use one hand to help hold door in position

by lifting up on rear burner housing or applying

pressure directly to the door while re-installing

the securing hardware with your opposite hand.

Always install right side latching hardware

(5/16" flange nut and flat washer) first,

then

install left side hinge hardware

(5/16" x 3-1/2"

lg. hex head flange bolt) second.

Apply

additional pressure while hand tightening the

hardware as far as possible, then release the

pressure.

Figure 13A: Partial Front View - Burner Swing Door Mounted to Boiler - Fully Closed and Secured

NOTICE

When securing burner swing door make sure door

is drawn-in equally on both sides.

Step 4.

Use a hand wrench to tighten door hardware

and

always start with the right side flange

nut first.

Use an alternating tightening method

from right side flange nut to left side flange

bolt to tighten door equally until sealed without

applying excessive torque.

Never

tighten left

side flange bolt first or tighten either piece of

hardware 100% without using the alternating

tightening method described above.

Failure to follow the prescribed procedure could

cause thread damage to casting or a leak in the

door seal. If left side flange bolt is tightened

before right side flange nut, right side of door

can

not

be drawn-in to provide an air tight seal,

as shown in Figure 13C. Applying excessive

torque will only cause thread damage.

E. INSPECT COMBUSTION CHAMBER TARGET

WALL AND LINER, AND SWING DOOR

GASKET.

1. Open burner swing door using procedure previously

outlined in Paragraph D of this section.

2. Using a flashlight, inspect the rear target wall and

liner. The target wall should be rigidly secured to

the rear boiler section. The combustion chamber

liner should be evenly distributed in the boiler

chamber. If either is damaged, they must be

replaced.

SECTION IV: PACKAGED BOILER ASSEMBLY (continued)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды