U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 68 / 96

More make-up water and higher concentrations of

contaminants damage the boiler sooner.

Our warranty

does not cover corrosion and sediment-related

damage.

Clearly it is in everyone's best interest to

prevent this type of failure. You can do your part by

ensuring that your system is leak-free, keeping leakage

to less than 2 percent of the total water volume each

month.

D. ATTENTION TO BOILER WHILE NOT IN

OPERATION.

NOTICE

If boiler is not used during winter time, it must be

fully drained to prevent freeze damage.

1. Spray inside surfaces with light lubricating or

crankcase oil using gun with extended stem so as to

reach all corners.

2. With steam boilers, at end of season add sufficient

water to fill boiler to top of water column and leave

it that way until fall when water should be drained

again to proper level. If at this time boiler water is

dirty, drain water, flush out boiler, and refill with

clean water to prescribed water level.

3. Always keep the manual fuel supply valve shut off

if the burner is shut down for an extended period of

time.

4. To recondition the heating system in the fall season

after a prolonged shut down, follow the instructions

outlined in Section X, Paragraphs A through K.

WARNING

This boiler contains controls which may cause the

boiler to shut down and not restart without service.

If damage due to frozen pipes is a possibility, the

heating system should not be left unattended

in cold weather; or appropriate safeguards and

alarms should be installed on the heating system

to prevent damage if the boiler is inoperative.

SECTION XIII: MAINTENANCE AND SERVICE INSTRUCTIONS (cont'd)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды