U.S. Boiler Company V8H SERIES Скачать руководство пользователя

Страница: 55 / 96

8. Steps outlined in Paragraph 5 and 6 above must

be repeated every time the Head/Turbulator or Air

Band/ Damper Setting is readjusted.

9. Turn “OFF” burner and remove Riello Combination

Pressure Gauge and Bleeder Valve Assembly.

Install pressure

port/bleeder plug and tighten. Start

burner again.

WARNING

DO NOT

loosen or remove any oil line fittings

while burner is operating.

10. FLAME FAILURE

The V8H boiler controls operate the burner

automatically. If for unknown reasons the burner

ceases to fire and the reset button on the primary

control has tripped, the burner has experienced

ignition failure. Refer to Oil Primary Control

features, Paragraph I, Step 2 of this Section and

Section XV, Troubleshooting, Paragraph B. If

the failure re-occurs, call your heating contractor

immediately before pressing the reset button.

WARNING

DO NOT attempt to start the burner when excess

oil has accumulated, when the boiler is full of

vapor, or when the combustion chamber is very

hot.

CHECK FOR CLEAN CUT OFF OF

BURNER.

1. AIR IN THE OIL LINE between fuel unit and

nozzle will compress when burner is on and will

expand when burner stops, causing oil to squirt from

nozzle at low pressure as burner slows down and

causing nozzle to drip after burner stops. Usually

cycling the burner operation about 5 to 10 times will

rid oil line of this air.

2. IF NOZZLE CONTINUES TO DRIP, repeat

Paragraph H, No. 1 above. If this does not stop the

dripping, remove cut-off valve and seat, and wipe

both with a clean cloth until clean, then replace

and readjust oil pressure. If dripping or after burn

persist replace fuel pump.

TEST CONTROLS.

1. Check thermostat operation. Raise and lower

thermostat setting as required to start and stop

burner.

WARNING

Before installation of the boiler is considered

complete, the operation of all boiler controls must

be checked, particularly the primary control and

high limit control.

VERIFY OIL PRIMARY CONTROL

FEATURES

using procedures outlined in

Instructions furnished with control or instructions as

follows:

GeniSys 7505 Control Features,

see Figure

30A.

The GeniSys 7505 is a microprocessor-

based control. The indicator light provides

diagnostic information for lockout, recycling

and cad cell status. There is a manual reset

button to exit the Lockout Mode.

ii.

Pump Priming Cycle: To facilitate purging

air from the oil lines and filters, the 7505 can

be placed in a purge routine by:

• After the burner starts, press and hold the

reset button for 15 seconds until the

SECTION XI: SYSTEM START-UP (continued)

Figure 29B: Electrode Positioning, Retention Ring

Assembly and Nozzle Adapter (Carlin EZ-1 / EZ-2)

Figure 29C: Combustion Head / Nozzle /

Electrode Settings (Carlin 102CRD)

Figure 29D: Electrode Positioning (Riello 40 Series)

Содержание V8H SERIES

































































































Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды

U.S. Boiler Company V8H SERIES, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание V8H SERIES

Отзывы:

Похожие инструкции для V8H SERIES

Бренды по названию

Популярные бренды