background image

8U.51.60.10 / 01.17 

  

Changes reserved.

I n s t a l l a t i o n   &   S e r v i c i n g 

Instructions

High effi

  ciency condensing gas boiler

E50CRN

E75CRN/E110CRN

E75CRP/E110CRP

-  Do not store or use gasoline or other fl ammable vapors and 

liquids in the vicinity of this or any other appliance.

-  WHAT TO DO IF YOU SMELL GAS

-  Do NOT try to light any appliance.
-  Do NOT touch any electrical switch. 
-  Do NOT use any phone in your building.
-  Immediately call your gas supplier from a neighbor’s phone. 

Follow the gas supplier’s instructions.

-  If you cannot reach your gas supplier, call the fi re department.

CAUTION!

Read this manual thoroughly before installing, servicing, putting 
into operation or using this boiler and vent system.

WARNING!

Improper  installation,  adjustment,  alteration,  service  or 
maintenance  can  cause  property  damage,  personal  injury 
(exposure  to  hazardous  materials)  or  loss  of  life.  Refer  to  the 
user's information manual provided with this boiler. Installation 
and service must be performed by a licensed professional, service 
agency or the gas supplier (who must read and follow the supplied 
instructions before installing, servicing, or removing this boiler).

CAUTION!

The user manual is part of the documentation that is delivered 
to the installation's operator. Go through the information in this 
manual  with  the  owner/operator  and  make  sure  that  they  are 
familiar with all necessary operating instructions.

NOTICE!

Installation  and  service  must  be  performed  by  a  qualifi ed 
installer, service technician or the gas supplier. 

In  the  Commonwealth  of  Massachusetts  this  boiler  must  be 
installed by a licensed Plumber or Gas Fitter.

WARNING!
If you do not follow these instructions exactly, a fi re or explosion 
may result causing property damage, personal injury or loss of life.

These instructions to be retained by user.

Address: 103 International Drive, Peachtree City, GA, 30269

Toll-free: 1-800-621-9419

 • 

Fax: 678-829-1666

 • 

www.rinnai.us

Pictured:  E50CRN
 

E75CRN, E110CRN

 

E75CRP, E110CRP

Wall-hung  Condensing  Boilers: 
E50CR, E75CR, E110CR

Summary of Contents for E110CRN

































































































Reviews: