background image

Installation and Operation Instructions 

Document 1276D

H2359200D

 

WARNING

If the information in these instructions is 

not followed exactly, a fire or explosion 

may result causing property damage, 

personal injury or death.

Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not 

use any phone in your building.

•  Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

•  If you cannot reach your gas supplier, call 

the fire department.

Installation and service must be performed 

by a qualified installer, service agency, or gas 

supplier.

FOR YOUR SAFETY:

 This product must be installed and serviced by a professional service technician, 

qualified in hot water boiler and heater installation and maintenance. Improper installation and/or operation 

could create carbon monoxide gas in flue gases which could cause serious injury, property damage, or 

death. Improper installation and/or operation will void the warranty.

 

AVERTISSEMENT

Assurez-vous de bien suivres les instructions 

données dans cette notice pour réduire au 

minimum le risque d’incendie ou d’explosion ou 

pour éviter tout dommage matériel, toute blessure 

ou la mort.

Ne pas entreposer ni utiliser d’essence ou ni 

d’autres vapeurs ou liquides inflammables dans 

le à proximité de cet appareil ou de tout autre 

appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

•  Ne pas tenter d’allumer d’appareils.

•  Ne touchez à aucun interrupteur. Ne pas vous servir 

des téléphones dans le bâtiment où vous vous trovez.

•  Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 

fournisseur.

•  Si vous ne pouvez rejoindre le fournisseur de 

gaz, appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par 

un installateur ou un service d’entretien qualifié ou 

par le fournisseur de gaz.

Modulating Boiler 

Water Heater

Model MGH1600 

Model MGV1600

1,600 MBTU/h 

1,600 MBTU/h 

Model MGH2000 

Model MGV2000

1,999 MBTU/h 

1,999 MBTU/h

Model MGH2500 

Model MGV2500

2,499 MBTU/h 

2,499 MBTU/h

Model MGH3000 

Model MGV3000

3,000 MBTU/h 

3,000 MBTU/h

Model MGH3500 

Model MGV3500

3,500 MBTU/h 

3,500 MBTU/h

Model MGH4000 

Model MGV4000

4,000 MBTU/h 

4,000 MBTU/h

Installation and
Operation Instructions for

M

AGNA

T

HERM

  

® 

 

Summary of Contents for MagnaTherm MGH1600





















































































































Reviews: