Tractel Supertirfor TU16H, Руководство по эксплуатации и обслуживанию

Страница: 40 / 96

- 18 -
For less intensive use, the oil change is performed once
per year.
To change the oil in the hydraulic power pack, remove the
screw (item 12, figure 1, page 7) located under the tank.
USED OIL MUST BE DISPOSED OF IN COMPLIANCE
WITH APPLICABLE REGULATIONS.
The drain screw has a magnetic part used to recover
metallic particles.
Carefully clean the screw before reinstalling it in its
housing.
Check that the drain screw and washer are correctly in
place before filling the tank with oil.
12.3 Gasoline engine
For the gasoline engine servicing operations, proceed as
instructed in the specific manual (appended to this
manual).
13. UNAUTHORIZED USED OF SUPERTIRFOR™
EQUIPMENT
Safe use of your SUPERTIRFOR™ equipment will be
ensured by following the instructions given in this manual.
The following unauthorized actions are strictly prohibited.
Do not:
- Use the machine described in this manual to lift persons.
- Secure the machine by any other means other than the
anchoring component provided with your unit.
- Block the machine in a fixed position or hinder self-
alignment of the machine in the direction of the load.
- Apply a load on a SUPERTIRFOR™ wire rope strand
coming out of the anchoring side.
- Knock on the control units.
- Use a TU16H and a TU32H simultaneously to lift or pull a
same load.
- Use a setup in which the SUPERTIRFOR™ machine
moves along the wire rope.
- Operate the machine in the forward direction to a point
that the wire rope hook comes into contact with the
casing.
- Operate the machine in the reverse direction to a point
where the wire rope end moves into the casing.
- Use the SUPERTIRFOR™ wire rope as a slinging means.
- Use any other wire rope other than a SUPERTIRFOR™
wire rope.
- Handle the wire rope without appropriate Personnel
Protection Equipment.
- Allow a tensioned wire rope to bear and rub against an
obstacle.
- Expose the wire rope to temperatures exceeding 100°C,
or to mechanical or chemical agents which could damage
the wire rope.
- Use the SUPERTIRFOR™ machine with any kind of
foreign matter inside the unit.
- Fit two rams simultaneously on a SUPERTIRFOR™
TU16H machine.
- Fit the extending control handle on the forward or reverse
operating levers when the SUPERTIRFOR™ machine is
equipped with a ram.
- Attempt to maneuver the clutch handle when the machine
has a load.
- Hinder free movement of the reverse operating lever, the
forward operating lever or the clutch handle.
- Simultaneously actuate the forward and reverse operating
levers.
- Use any other means of maneuvering the machine other
than the original extending handle or the ram.
- Replace the SUPERTIRFOR™ safety pins with anything
other than genuine SUPERTIRFOR™ safety pins of the
same model.
- Use greases or oils containing molybdenum disulfide or
graphite additives to lubricate the wire rope or the
machine.
- Connect a TU16H to an outlet marked “TU32H”.
- Operate a hydraulic power pack without oil in the tank.
- Connect more than 4 rams to a same hydraulic power
pack.
- Throw away used oil without complying with applicable
environment protection regulations.
- Fill the fuel tank of the gasoline engine while the engine is
running.
- Smoke near a hydraulic power pack with gasoline engine
when filling the engine tank with fuel.
- Use any other fuel than the fuel recommended.
- Use the power pack with gasoline engine in a closed
room, even if the doors or windows are open. The
gasoline engine produces carbon monoxide which is a
poisonous, odour-free, invisible gas. Inhalation of carbon
monoxide can cause nausea, fainting and death.
- Place anything on the exhaust pipe or on the body of the
gasoline engine when in use or after use of the engine.
The metal parts of the gasoline engine conduct heat and
can cause burns when in contact with human skin.
- Run the electric motor in the counter-clockwise direction.
- Connect the hydraulic power pack with electric motor
without a proper ground connection.
- Use the machine when the electrical protection devices
are not properly sized.
- Block the electric motor control button in the “on” position
using an external device.
- Touch the fins while the motor is turning.
- Pull the hydraulic power pack by its power cable.
GB