Toro Sand Pro 2040Z Скачать руководство пользователя

Страница: 13 / 60

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

No parts required

–

Remove the shipping board.

Attachment and related parts (sold
separately)

–

Install an attachment.

Front weights (as needed per
attachment)

–

Install the front weights.

Bolt (5/16 x 3/4 inch)

Nut (5/16 inch)

Connect the battery (Model 08706TC
only).

Warning decal (130-1851)

Apply the CE warning decal, if required
(Model 08706TC only).

Service decal (130-2620)

Apply the CE service decal, if required
(Model 08706TC only).

Roll bar

Bolt

Flange locknut

Spring washer

Bracket

Install the ROPS (Model 08706TC only).

Media and Additional Parts

Description

Qty.

Use

Operator's Manual

Engine operator's manual

Operator training materials

Pre-delivery inspection sheet

Read the sheet before operating.

Parts Catalog

Use the catalog to order parts.

Certificate of Compliance

The certificate indicates CE compliance.

Key

Start the engine.

Note:

Determine the left and right sides of the machine from the normal operating position.

Note:

Remove and discard all the shipping brackets and fasteners.

Содержание Sand Pro 2040Z





























































Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды

Toro Sand Pro 2040Z, Руководство оператора

Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды