Toro Sand Pro 2040Z Скачать руководство пользователя

Страница: 50 / 60

G023651

Figure 68

Stop screw

Allow the governor arm to return to the original
position.

Loosen the jam nut on the low-idle speed setscrew.

Adjust the low-idle speed setscrew so that the idle
speed is 1450 to 1650 rpm.

Tighten the jam nut.

Adjust the high-idle speed as follows:

Important:

Do not adjust the high-idle speed with the

air cleaner removed.

Start the engine and allow it to warm up thoroughly.

Loosen the jam nut on the high-idle speed setscrew
a few turns.

Move the throttle control so that the idle speed is 2750
to 2950 rpm.

Tighten the high-idle speed setscrew so that it just
touches the tab on the speed-control lever.

G023672

Figure 69

Jam nut

High-idle speed setscrew

Low-idle speed setscrew

Speed-control lever

Tab (on the speed-control
lever)

Tighten the jam nut.

Содержание Sand Pro 2040Z





























































Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды

Toro Sand Pro 2040Z, Руководство оператора

Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды