Toro Sand Pro 2040Z Скачать руководство пользователя

Страница: 11 / 60

127–7868

Warning—do not operate the machine without the
attachment installed.

130–2620

CE only

Read the

Operator’s Manual

for information on maintenance. 15.

Hydraulic oil

Check every 8 operating hours.

16.

Fuel tank/filter

Oil level—engine

17.

Capacity

Oil level—hydraulic tank

18.

Service interval

Neutral interlock switch

19.

Filter part number

Air filter

20.

Read the

Operator’s Manual

for information on

fuses—Headlights 15A; Attachment 10A; Engine start 25A;
Battery 20A.

Tire pressure (0.48 bar)

21.

Belt routing

Wheel nut torque (61 to 75 N-m)

22.

Left-hand driven pulley

Battery

23.

Belt tensioner

10.

Fuel—gasoline only

24.

Drive pulley

11.

Seat interlock switch

25.

Right-hand driven pulley

12.

Check every 100 operating hours.

26.

Belt tensioner—part number (replace every 800 operating
hours)

13.

Lubrication

27.

Belt—part number (replace every 800 hours)

14.

Engine oil

Содержание Sand Pro 2040Z





























































Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды

Toro Sand Pro 2040Z, Руководство оператора

Результаты поиска

Содержание Sand Pro 2040Z

Отзывы:

Похожие инструкции для Sand Pro 2040Z

Бренды по названию

Популярные бренды