Toro Reelmaster 5510 Series Скачать руководство пользователя страница 400 | Manualshive

Страница: 400 / 662

background image

Electrical System Quick Checks

Testing the Battery (Open Circuit Test)

Use a multimeter to measure the voltage between the battery terminals; refer to

Battery Test Table (page 7–44)

.

Set the multimeter to the DC volts settings. The battery must be at a temperature
of 16°C to 38°C (60°F to 100°F). Ensure that the key switch is in the O

FF

position

and all the accessories are turned off.

Connect the positive (+) multimeter lead to the positive battery post and negative
(-) multimeter lead to the negative battery post.

Measure and record the battery voltage. Use the

Battery Test Table (page 7–44)

to determine charge level of the battery.

Note:

This test provides a relative condition of the battery. The load testing of

the battery provides additional and more accurate information; refer to

the Battery (page 7–125)

.

Battery Test Table

Voltage Measured

Battery Charge Level

12.68 V (or higher)

Fully charged (100%)

12.45 V

75% charged

12.24 V

50% charged

12.06 V

25% charged

11.89 V

0% charged

Testing the Charging System

This is a simple test that determines if a charging system is functioning. It tells
you if the charging system has an output, but not its capacity.

Note:

The InfoCenter display can be used to identify battery voltage during

the operation of the machine.

Tool required: Digital multimeter set to DC volts.

Test instructions: Connect the positive (+) multimeter lead to the positive battery
post and negative (-) multimeter lead to the negative battery post. Keep the test
leads connected to the battery posts and record the battery voltage.

Note:

When starting the engine, the battery voltage drops and then must

increase once the engine is running.

Note:

Depending upon the condition of the battery charge and battery

temperature, the battery voltage increases at different rates as the battery
charges.

Start the engine and run it at high-idle speed

(3,005 to 3,055 rpm)

. Allow the

battery to charge for a minimum time of 3 minutes. Record the battery voltage.

Note:

After running the engine for a minimum time of 3 minutes, the battery

voltage must be minimum 0.50 V higher than that of the initial battery voltage.

Refer to the

Battery Voltage Table (page 7–45)

for an example of a charging

system that is functioning.

Electrical System: Electrical System Quick Checks

Page 7–44

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

«
...
398
399
400
401
402
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: B&G Страницы: 3

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Tanaka Страницы: 20

Бренд: Garmin Страницы: 2

Robus RVB007RGB10I65

Бренд: LED Group Страницы: 2

Бренд: Monosem Страницы: 52

Бренд: Wiltron Страницы: 13

Бренд: Kellfri Страницы: 24

V-M.O.L.E. Solar

Бренд: ECD Страницы: 16

Бренд: Garten Meister Страницы: 80

Бренд: Ibiza Страницы: 32

ChemiDoc XRS 170-8070

Бренд: BIO RAD Страницы: 42

Digital Delay DD-6

Бренд: Boss Страницы: 28

Бренд: Chauvet Professional Страницы: 48

Бренд: HQ Power Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды