Toro Reelmaster 5510 Series Скачать руководство пользователя страница 270 | Manualshive

Страница: 270 / 662

background image

Charging the Hydraulic System (continued)

2. After the hydraulic system components have been properly installed and if

the traction pump was rebuilt or replaced, ensure that the traction pump
housing is at least half full of clean hydraulic fluid.

3. Ensure that all of the hydraulic connections, lines, and components are

secured tightly.

Note:

Flush and fill the hydraulic system and tank whenever there is a

severe component failure or the system is contaminated; refer to

the Hydraulic System (page 6–147)

.

4. Ensure that the hydraulic tank is full. Add correct quantity of hydraulic fluid if

necessary; refer to the

Operator’s Manual

.

5. Check the control linkage for proper adjustment, binding, or damaged parts.

6. Prime the hydraulic pumps; refer to

Priming the Hydraulic Pumps (page

.

IMPORTANT

Before lifting the machine with a jack, review and follow

Instructions (page 1–6)

.

7. Lift and support the machine with jack stands so that all the drive wheels

are off the ground.

CAUTION

Ensure that the machine is safely supported so that it does not move
or accidentally fall and prevent injuring anyone under the machine.

8. Ensure that the traction pedal is in the N

EUTRAL

position. Start the engine

and run it at low-idle speed.

Note:

The hydraulic pumps must pick up the hydraulic fluid and fill the

hydraulic system. If there is no indication of fill in 30 seconds, shut off the
engine and find the cause.

9. After the hydraulic system starts to show the signs of fill, actuate joystick

switches until the lift cylinder rod moves in and out several times.

10. If the lift cylinder does not move after 3 to 5 seconds or if the pump emits

abnormal sounds, shut off the engine immediately, and find the cause or
problem. Inspect for the following:

A. The oil filter or suction lines that are loose.

B. An incorrect hose routing.

C. The suction line that is blocked.

D. The charge relief valve in the traction pump that is damaged.

E. The gear pump that is damaged.

11. After the lift cylinder moves normally, proceed to step

12. Turn the steering wheel in both directions so that the steering cylinders move

in and out several times.

13. Operate the traction pedal in the forward and reverse directions. The drive

wheels should rotate in the proper direction. If the wheels rotate in the
wrong direction, shut off the engine, inspect the hydraulic line placement at

Hydraulic System: Service and Repairs

Page 6–152

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

«
...
268
269
270
271
272
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: B-K lighting Страницы: 3

Бренд: Waterpik Страницы: 2

Бренд: WaterUps Страницы: 2

Бренд: Landoll Страницы: 38

Бренд: RAMVAC Страницы: 53

Бренд: Lumineux Страницы: 2

TRAKTOR KONTROL S3

Бренд: Native Instruments Страницы: 39

Бренд: Baldan Страницы: 72

Бренд: SATA Страницы: 294

Бренд: IKAR Страницы: 152

Бренд: HAMPTON BAY Страницы: 18

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды