Toro Reelmaster 5510 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 662

background image

High Flow Hydraulic Filter Kit

Toro Part Number: TOR6011

The high flow hydraulic filter kit is designed with
large flow (150 L/minute or 40 gallons/minute)
and high pressure (34,500 kPa or 5,000 psi)
capabilities. This kit provides for bi-directional
filtration which prevents filtered unwanted material
from entering into the circuit regardless of the flow
direction.

If a component failure occurs in the closed loop
traction circuit, contamination from the damaged
part will remain in the circuit until you remove it.
Install a high flow hydraulic-fluid filter into the circuit
when you connect the hydraulic test gauges in
order to test the traction circuit components or after
you replace a failed traction circuit component
(e.g., piston pump or wheel motor). This filter
removes contamination from the hydraulic fluid in
the traction circuit, thereby preventing additional
component damage.

Note:

This kit does not include the hydraulic hoses;

refer to

Hydraulic Hose Kit (page 2–13)

.

Note:

The replacement filter element is Toro

Part No. TOR6012. The filter element canister
tightening torque is

34 N∙m (25 ft-lb)

.

Remote Starter Switch

After flushing the hydraulic system or
replacing a hydraulic component (e.g.
gear pump, piston pump, drive motor), it is
necessary to prime the hydraulic pumps.
A remote starter switch can be used for
this purpose. A remote starter switch
can be purchased locally or fabricated as
follows.

IMPORTANT: When using a
remote starter switch, it is highly
recommended to include a 20 amp
in−line fuse between the battery and
switch connector for circuit protection.

A remote stater switch can also be
constructed using Toro switch #106−2027,
a length of 14 gauge wire, a 20 amp
in−line fuse, two (2) alligator clips and
necessary connectors. Connecting the
wire to switch terminals 1 and 2 will allow
the momentary switch contacts to be used
for the remote starter switch.

Note:

For information on using the remote

starter switch to prime the hydraulic
pumps.

Remote Starter Switch (purchased)

Remote Starter Switch (fabricated)

Reelmaster

®

5410/5510/5610 Series

Page 2–15

Specifications and Maintenance: Special Tools

15216SL Rev C

«
...
31
32
33
34
35
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Бренд: Gardena Страницы: 13

Бренд: Rain Harvesting Страницы: 2

Бренд: Hands Free Farm Страницы: 24

CIRCOLINA G10q T9

Бренд: Life Страницы: 2

TEMSTM POCKET 7.3

Бренд: ASCOM Страницы: 8

Бренд: American DJ Страницы: 8

Бренд: Civemasa Страницы: 55

Бренд: Heitronic Страницы: 16

Бренд: Swim & Fun Страницы: 17

Бренд: Halemeier Страницы: 2

Бренд: IRUDEK Страницы: 19

Street Bar IP65 16x3W TW

Бренд: Varytec Страницы: 52

Бренд: SDI Страницы: 20

Бренд: Megatel Страницы: 4

Бренд: Furuno Страницы: 8

BIG ZINNAKIS ATEX

Бренд: X-lite Страницы: 12

LED Zoom Par 18x12WRGBWlighting

Бренд: Shehds Страницы: 3

Бренд: Vari Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды