Toro Reelmaster 5510 Series Скачать руководство пользователя страница 456 | Manualshive

Страница: 456 / 662

background image

Engine Run Solenoid (Machine with Kubota Diesel Engine)

g228835

Figure 268

1.

Injection pump

2.

Fuel stop solenoid

The engine run solenoid used on a machine with a Kubota diesel engine must
be energized for the diesel engine to run. The Toro Electronic Controller (TEC)
controls the operation of the engine run solenoid. The solenoid is mounted to the
injection pump on the engine (

).

Testing the Engine Run Solenoid

1. Park the machine on a level surface, lower the cutting units, shut off the

engine, apply parking brake, and remove key from the key switch. Open
hood to get access to engine.

2. Disconnect wire harness connector from fuel stop solenoid.

Note:

The fuel stop solenoid may be removed from the engine or tested

in place.

3. If the solenoid is removed from the engine, ensure that the solenoid plunger

moves freely and is free of dirt, unwanted material, and corrosion.

Note:

Prior to taking small resistance readings with a digital multimeter,

short the test leads together. The meter will display a small resistance value
(usually 0.5 ohms or less). This resistance is due to the internal resistance
of the meter and test leads. Subtract this value from the measured value of
the tested component.

g228836

Figure 269

1.

Fuel stop solenoid

2.

Pull coil terminal

3.

Hold coil terminal

4. Use a digital multimeter (ohms setting), touch one test lead to the pull coil

terminal and the other test lead to the fuel stop solenoid frame (ground)

Electrical System: Testing the Electrical Components

Page 7–100

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

«
...
454
455
456
457
458
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: KaVo Страницы: 49

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hakko Electronics Страницы: 16

Бренд: Vari Lite Страницы: 14

Бренд: LCG Страницы: 11

Бренд: Cameo Страницы: 44

Бренд: Schreder Страницы: 15

Бренд: PARO Страницы: 20

Horizon PN 4000

Бренд: KARAM Страницы: 22

Water-pro Compact S-60 12v

Бренд: ECO SISTEMS Страницы: 30

Бренд: SIGLENT Страницы: 188

Бренд: Hatco Страницы: 56

Бренд: Farm21 Страницы: 18

Бренд: KN Sales Страницы: 22

Бренд: 9dot Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды