manualshive.com logo in svg

Toro Reelmaster 5510 Series, Руководство по обслуживанию


Поделиться
Скачать
background image

Chapter 7

Electrical System

Table of Contents

General Information .............................................................................................................................. 7–3

Electrical Schematic and Wire Harness Drawings/Diagrams ............................................................. 7–3
Toro Electronic Controller (TEC) ........................................................................................................ 7–3
CAN-bus Communications................................................................................................................. 7–3
Yanmar Engine Electronic Control Unit (ECU) ................................................................................... 7–4
Yanmar Engine Electrical Components.............................................................................................. 7–5
Kubota Gasoline Engine Electronic Control Unit (ECU)...................................................................... 7–5
Kubota Gasoline Engine Electrical Components................................................................................ 7–5

Special Tools ......................................................................................................................................... 7–7

Multimeter .......................................................................................................................................... 7–7
Terminal Protector.............................................................................................................................. 7–7
Battery Hydrometer............................................................................................................................ 7–7
Dielectric Gel...................................................................................................................................... 7–8

InfoCenter Display ................................................................................................................................. 7–9

Splash Screen.................................................................................................................................. 7–11
Main Information Screen .................................................................................................................. 7–12
Operator Advisory Screen................................................................................................................ 7–13
Main Menu Screen ........................................................................................................................... 7–14
Faults Screen................................................................................................................................... 7–16
Service Screen................................................................................................................................. 7–18
Diagnostics Screen .......................................................................................................................... 7–19
Settings Screen................................................................................................................................ 7–21
About Screen ................................................................................................................................... 7–25

Troubleshooting ................................................................................................................................... 7–26

Operator Advisories ......................................................................................................................... 7–26
Using the InfoCenter Display for Troubleshooting ............................................................................ 7–28
Machine Faults................................................................................................................................. 7–32
Engine Faults ................................................................................................................................... 7–35
General Run and Transport Problems.............................................................................................. 7–39

Electrical System Quick Checks .......................................................................................................... 7–44

Testing the Battery (Open Circuit Test) ............................................................................................. 7–44
Testing the Charging System ........................................................................................................... 7–44
Testing the Glow Plug System (Machines with Kubota Diesel Engine).............................................. 7–45
Checking the Operation of the Interlock Switches ............................................................................ 7–45

Adjustments......................................................................................................................................... 7–46

Traction Neutral Switch .................................................................................................................... 7–46
Parking Brake Switch ....................................................................................................................... 7–48
Cutting Unit Down Limit Switch ........................................................................................................ 7–50
Mow/Transport Switch...................................................................................................................... 7–52

Testing the Electrical Components....................................................................................................... 7–54

Fusible Link Harness (Machines with Kubota or Yanmar Diesel Engine) .......................................... 7–54
System Fuses .................................................................................................................................. 7–56
Engine Fuses (Gasoline Engine)...................................................................................................... 7–59
Toro Electronic Controller (TEC) ...................................................................................................... 7–61
Key Switch ....................................................................................................................................... 7–64
Reel Engage Switch......................................................................................................................... 7–66
Engine Speed Switch (If Equipped).................................................................................................. 7–68
Lower/Raise Joystick Switches ........................................................................................................ 7–70

Reelmaster

®

5410/5510/5610 Series

Page 7–1

Electrical System

15216SL Rev C

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Barko Hydraulics 930 Service Manual preview
930
Бренд: Barko Hydraulics Страницы: 92
Campbell CS500 Instruction Manual preview
CS500
Бренд: Campbell Страницы: 18
Vector 0 Owner'S Manual & Warranty Information preview
0
Бренд: Vector Страницы: 4
MacDon 3020 Operator'S Manual preview
3020
Бренд: MacDon Страницы: 88
JB Systems Sirius Operation Manual preview
Sirius
Бренд: JB Systems Страницы: 7
3B SCIENTIFIC PHYSICS 1023095 Instruction Sheet preview
1023095
Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36
Bacharach Fyrite INSIGHT Operating & Maintenance Instructions preview
Fyrite INSIGHT
Бренд: Bacharach Страницы: 31
Bacharach Monoxor III Specification Sheet preview
Monoxor III
Бренд: Bacharach Страницы: 2
Mandam MCH Series Instruction Manual preview
MCH Series
Бренд: Mandam Страницы: 9
EarthQuake 9800B Operating & Parts Manual preview
9800B
Бренд: EarthQuake Страницы: 12
Laserworld EL-60 G Manual preview
EL-60 G
Бренд: Laserworld Страницы: 8
Laserworld EL 200 LED User Manual preview
EL 200 LED
Бренд: Laserworld Страницы: 6
LaserLiner ActivePen Manual preview
ActivePen
Бренд: LaserLiner Страницы: 56
LaserLiner AC-tiveMaster Operating Instructions Manual preview
AC-tiveMaster
Бренд: LaserLiner Страницы: 54
R&S RTC1000 User Manual preview
RTC1000
Бренд: R&S Страницы: 371
R.M. Young 06206 Instructions Manual preview
06206
Бренд: R.M. Young Страницы: 9
Walimex Pro LED Round 200 Instruction Manual preview
LED Round 200
Бренд: Walimex Pro Страницы: 44
Exalto 2178.085 Manual preview
2178.085
Бренд: Exalto Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды