Toro Reelmaster 5510 Series Скачать руководство пользователя страница 349 | Manualshive

Страница: 349 / 662

background image

Disassembling the Steering Cylinder (continued)

beveled edge of the retaining ring to start the retaining ring through the
opening. Rotate the head counterclockwise to remove the retaining ring
from the barrel and head..

4. Remove the plugs from the ports. Carefully twist and pull the shaft and

remove the shaft with head and piston.

IMPORTANT

Clamping the vise jaws against the shaft surface could damage the
shaft. When securing the shaft in a vise, clamp the shaft clevis only.

5. Use a wrench on shaft flats to prevent the shaft from rotating, remove the

locknut.

6. Carefully slide the piston and then head off the shaft.

Note:

Do not scratch or damage the piston.

7. Remove the wear ring, BP seal, and O-ring from the piston.

Note:

Do not scratch or damage the head.

8. Remove the O-ring, back-up washer, dust seal, and BS seal from the head.

9. Discard the seals and O-rings that were removed.

Inspecting the Steering Cylinder

CAUTION

Use eye protection such as goggles when using compressed air.

1. Wash all the cylinder components in clean solvent and dry them with

compressed air.

2. Inspect the internal surface of the barrel for deep scratches, out-of-roundness,

and bending.

3. Inspect the head, shaft, and piston for excessive pitting, scoring, and wear.

4. Replace the steering cylinder if the internal components are worn or

damaged.

Assembling the Steering Cylinder

1. Ensure that all the parts are clean before assembly.

2. Put a coating of clean hydraulic fluid on new O-rings, back-up washer, and

other seals.

A. Carefully install the wear ring, BP seal, and O-ring to the piston.

B. Carefully install the back-up washer, O-ring, dust seal, and BS seal

to the head.

3. Put a coating of clean hydraulic fluid on the shaft. Slide the head and piston

onto the shaft.

IMPORTANT

Clamping the vise jaws against the shaft surface could damage the
shaft. When securing the shaft in a vise, clamp the shaft clevis only.

Reelmaster

®

5410/5510/5610 Series

Page 6–231

Hydraulic System: Service and Repairs

15216SL Rev C

«
...
347
348
349
350
351
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Бренд: Pall Страницы: 51

Бренд: unios Страницы: 2

Frontier FC5706

Бренд: OHAUS Страницы: 47

Бренд: Guyatone Страницы: 2

Бренд: Fisher Scientific Страницы: 44

Бренд: Ametek Страницы: 20

L10 LVELED Series

Бренд: Clevetronics Страницы: 2

Бренд: Goobay Страницы: 20

Бренд: Gronomics Страницы: 2

Бренд: Monosem Страницы: 92

Бренд: Original BTC Страницы: 2

Wensco AnPro180 Stick

Бренд: G2G Lighting Страницы: 3

DS-CDJ-250 MKII

Бренд: DAPAudio Страницы: 19

Бренд: Oakton Страницы: 2

EXPERTmatic LUX E15 L

Бренд: KaVo Страницы: 72

Бренд: ProLights Страницы: 44

Бренд: Akai Страницы: 28

Бренд: Claind Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды