TLV EF200F-C Скачать руководство пользователя страница 132

Страница: 132 / 181

Diagnostics and troubleshooting

EF200F-C

132

Diagnostic

number

Short text

Remedy instructions

Status

signal

[from the

factory]

Diagnostic

behavior

[from the

factory]

946

Vibration detected

Check installation

Warning

947

Vibration exceeded

Check installation

Alarm

948

Signal quality bad

1. Check process conditions: wet

gas, pulsation

2. Check installation: vibration

Warning

972

Degrees of superheat
limit excceeded

1. Controll process conditions
2. Install pressure transmitter or

enter correct ﬁxed pressure value

Warning

Diagnostic behavior can be changed.

12.4.1 Operating conditions for displaying the following diagnostics

information

Operating conditions for displaying the following diagnostics information:
• 871 Near steam saturation limit diagnostic message: The process temperature is

less than 2K from the saturated steam line.

• Diagnostics information 872: The measured steam quality has dropped below the

conﬁgured limit value for the steam quality (limit value: Expert → System
→ Diagnostic handling → Diagnostic limits → Steam quality limit).

• Diagnostics information 873: The process temperature is 侑 0

• Diagnostics information 874: Wet steam detection/measurement is outside the

speciﬁed limits for the following process parameters: pressure, temperature,
velocity.
• Pressure: 0.5 to 100 bar
• Temperature: +81.3 to +320

C (+178.3 to +608

• Velocity: Depends on the measuring tube and is conﬁgured via EhDS.

• Diagnostics information 972: The degree of superheat has exceeded the conﬁgured

limit value (limit value: Expert → System → Diagnostic handling → Diagnostic limits
→ Degrees of superheat limit).

12.4.2 Emergency mode in the event of pressure compensation

Disable the pressure measuring cell: in the Disable pressure cell parameter (7747)
select the Yes option.

The measuring device uses the ﬁxed process pressure to calculate.

12.4.3 Emergency mode in event of temperature compensation

Change temperature measurement: PT1+PT2 to the PT1 option, PT2 option or the Oﬀ
option.

If the Oﬀ option is selected, the measuring device calculates by using the ﬁxed
process pressure.

►

Содержание EF200F-C





















































































































































































Результаты поиска

Содержание EF200F-C

Отзывы:

Похожие инструкции для EF200F-C

Бренды по названию

Популярные бренды

TLV EF200F-C, Инструкция по эксплуатации

Результаты поиска

Содержание EF200F-C

Отзывы:

Похожие инструкции для EF200F-C

Бренды по названию

Популярные бренды