TECO 7300EV Скачать руководство пользователя страница 9

Страница: 9 / 93

Chapter 1

Safety Precautions

1-3

1.1.5 During operation

Danger

Do not connect or disconnect the motor while inverter is operating the motor, Otherwise the inverter
and the diconnect device will be damaged by the high level of switch off current.

Danger

To avoid electric shock, do not take the front cover off. during power on.

The motor will restart automatically after stop when auto-restart function is on. In this case, care must

be taken while working with the machine.

Note: The operation of stop switch is different to that of the emergency stop switch.

Stop switch has to be activated for it to be effective. Emergency stop has to be de-
activated to become effevtive.

Caution

Do not touch heat-generating components such as heat sink and brake resistor.

The inverter can drive the motor running from low speed to high speed. Verify the allowable speed

ranges of the motor and the mechnism.

Note the settings related to the braking unit.

Do not check signals on circuit PCB while the inverter is running.

Caution

Allow a minimum of 5 minutes power down before attempting to disassemble or checking
the components within the drive.

1.1.6 Useable environment

Caution

When the inverter top dust cover has been removed can be used in a non-condensed
environment with temperature from –10

C to +50

C and relative humidity of 95%, but the

environment should be free from water and metal dust.

Содержание 7300EV






























































































Результаты поиска

Содержание 7300EV

Отзывы:

TECO 7300EV, Быстрый старт, Страница: 9 / 93

Результаты поиска

Содержание 7300EV

Отзывы: