TECO 7300EV Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 93

TECO 7300EV Скачать руководство пользователя страница 57

Chapter 4 Software index

4-24

F50 Low frequency voltage compensation, C14=000

Performance: During low frequency
Increase F50 setting value can increase output voltage and low frequency torque.
Decrease F50 setting value can decrease output voltage and low frequency torque.

• Output voltage/frequency curve pattern:

• Operating frequency range:

• During low frequency use:
When the motor output torque is not enough and increase F50 setting value.
When the motor is vibration and decrease F50 setting value.

F51 Advanced parameter
function display

000:Disable access to advanced parameters ( Group C )
001:Enable access to advanced parameters ( Group C )

F51=000. Parameter group C can not be displayed or accessed.
F51=001. Enable display and access parameter group C .

F52 Factory default

010: Reset parameters to factory default (50Hz)
020: Reset parameters to factory default (60Hz)

F53 Software version

F54 Fault records (Latest 3 times)

Advanced Parameters List ( Group C parameters)

C00 Reverse run

000: Reverse enable

001: Reverse disable

F04=000 and C00=001, F03 (motor direction) disable, the inverter is set to forward operation.
F04=001 or 002, and C00=001, reverse command is disable.

F50

V

F

0~12HZ / 60HZ
0~10HZ / 50HZ

«
...
55
56
57
58
59
...
»

Содержание 7300EV






























































































Отзывы:

Нет отзывов