TECO 7300EV Скачать руководство пользователя страница 11

Страница: 11 / 93

Chapter 3 Environment description and installation

3-1

Chapter 3 Environment description and installation

3.1Environment

The environment will directly affect the proper operation and the life of the inverter, so install
the inverter in an environment complies with the following conditions:

Ambient temperature: -10

~+50

℃

Avoid exposure to rain or moisture.

Avoid direct sunlight.

Avoid smoke and salinity.

Avoid erosive liquid and gas.

Avoid dust, bats, and small metal pieces.

Keep away from radiative and flammable

materials.

Avoid electromagnetic interference (soldering machine, power machine).

Avoid vibration (punching machine). Add a vibration-proof pad if the situation can not be

avoided.

If several inverters are placed in the same control panel, add extra heat dissipators to keep

the temperature below 50

(Correct configuration)

(Incorrect configuration)

(Correct configuration)

(Incorrect configuration)

Place the front side of the inverter onward and top upward to help heat dissipation.

(A)Front view (B)Side view

Inside the power
distributor

Inside the
power
distributor

Air exchanging fan

Inside the
power
distributor

Содержание 7300EV






























































































Результаты поиска

Содержание 7300EV

Отзывы:

TECO 7300EV, Быстрый старт, Страница: 11 / 93

Результаты поиска

Содержание 7300EV

Отзывы: