TECO 7300EV Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 93

TECO 7300EV Скачать руководство пользователя страница 6

Chapter 0 Preface

0-1

Chapter 0 Preface

0.1 Preface

To extend the performance of the product and ensure your safety, read this manual thoroughly before
using the inverter. Should there be any problem in using the product and can not be solved with the
information provided in the manual, contact your nearest TECO distributor or our sales representatives
who will be willing to help you. Please keep using TECO’s products in the future.

※

Precautions

The inverter is an electrical electronic product. For your safety, there are symbols such as “Danger”,
“Caution” in this manual to remind you to pay attention to safety instructions on carrying, installing,
operating, and checking the inverter. Be sure to follow the instructions for highest safety.

Indicates a potential hazard that causes death or serious personal injury
if misused

Indicates that the inverter or the mechanical system might be damaged if
misused

Danger

z

Do not touch any circuit boards or parts if the charging indicator is still lit after turning

the power off.

z

Do not connect any wires when the inverter is powered. Do not check parts and signals on

circuit boards when the inverter is in operation.

z

Do not disassemble the inverter and modify internal wires, circuits and parts.

z

Ground the ground terminal of the inverter properly, for 200V class ground to 100

ȍ

or

below, 400v class ground to 10

ȍ

or below.

0.2Products Inspection

TECO’s inverters are all passed the function test before delivery. Please check the followings
when you receive and unpack the inverter:

z

The model and capacity of the inverter is the same as those specified on your order.

z

Is there any damage caused by transportation. If so, do not apply the power.
Contact TECO’s sales representatives if any of the above problems happened.

Caution

z

Do not perform a voltage test on parts inside the inverter. High voltage will easily destroy

these semiconductor parts.

z

Do not connect T1 (U), T2 (V), and T3 (W) terminals of the inverter to AC power source.

z

CMOS ICs on the inverter’s main board are sensitive to static electricity. Do not touch the

main board.

Danger

Caution

«
...
4
5
6
7
8
...
»

Содержание 7300EV






























































































Отзывы:

Нет отзывов