TECO 7300EV Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 93

TECO 7300EV Скачать руководство пользователя страница 55

Chapter 4 Software index

4-22

Corresponding list of current and carrier frequency

F41 Auto restart on momentary power loss. 000:

Enable

001:

Disable

F41=000: Auto restart after a momentary power loss is enabled on resumption of power and
application of run signal, according to setting of parameter F4.
The Inverter will carry out an auto speed search, once the motor spinning speed is found then it will
accelerate to the running speed before the power loss.
F41=001: Disable.

F42 Auto restart times: 000 ~ 005

1.) F42=000: The inverter will not auto-restarted on fault trip.
2.) F42>000
The Inverter will carry out an auto search 0.5 sec after the fault trip, and while
the inverter output is switched off and the motor is coasting to stop.
Once the spinning speed is determined the inverter will accelerate or decelerate to speed before the
fault.
3.) Auto restart is not include OL1, OL2, OH, BB, warning.
Note:- Auto restart will not function while DC injection breaking or deceleration to stop
Is performed.

F43 Motor rated current

（

A

）

F44 Motor rated voltage

（

Vac

）

F45 Motor rated frequency (Hz)
F46 Motor rated power (KW)
F47 Motor rated speed (RPM)

F48 Torque boost gain (Vector), C14=000

Performance: If detection the motor load is too large increase the output torque.

(load current) (compensation gain)

Model

Carrier
frequency

EV-1P2/2P2

H1/H1F/H3

EV-1P5/2P5

H1/H1F/H3

EV-101/201

H1/H1F/H3

EV-202

H1/H1F/H3

EV-203

H1/H1F/H3

EV-401

H3/H3F

EV-402

H3/H3F

EV-403

H3/H3F

4~10K 1.7 3.1 4.2 7.5 10.5

2.3

3.8

5.2

12K

1.7

3.1

4.2

7.5

10.5

14K

1.6

3.0

4.0

7.0

10

16K 1.5 2.8 3.8 6.8 9.8

Δ

Te

≒

I

¯

Gain

«
...
53
54
55
56
57
...
»

Содержание 7300EV






























































































Отзывы:

Нет отзывов