TECO 7300EV Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 93

TECO 7300EV Скачать руководство пользователя страница 53

Chapter 4 Software index

4-20

Multi-function analog output:
F26 Multi-function output analog type selection

001: Set frequency
002: Output frequency
003: DC voltage
004: Output current
005:PID feedback signal

F27 Multi-function analog output gain = 000 ~ 200%

0-10 Vdc output from FM+ multi-function analog output terminal.
Output can be set to any of the above selections.

F27 is used to scale the output signal supplied to the externally connected analog device.

F26=005, PID Feedback. The analog input to terminal AIN ( 0-10vdc or 4-20mA),will be output
from terminal FM+ as 0-10Vdc.
Note: Due to hardware limits, the max output voltage from FM+ terminal will be limited to 10V.

Keypad, jog and preset frequency setting (MFIT)

：

Note1 :- Frequency selection will be made according to the setting of terminals S1-S4 & AIN and
also setting of parameters F11 – F15 as required.
Note2:- Selected preset frequency values should be programmed in parameters F28- F36 as
required.

1) F11~F15=002-004 (Preset frequency Command 1~3)

When run signal is applied and any of the selected multi-function input terminals is ON, the
inverter will run at the preset frequency according to the table below.

2) F11~F15=005 (Jog Frequency Command)

External input terminal is set to Jog operation. As it is on, the inverter will run at Jog
frequency.

Parameter

Description

Frequency range

Factory default

F28

Preset frequency 1 (Hz)

00.0 - 200

05.0

F29

Preset frequency 2 (Hz)

00.0 - 200

05.0

F30

Preset frequency 3 (Hz)

00.0 - 200

10.0

F31

Preset frequency 4 (Hz)

00.0 - 200

20.0

F32

Preset frequency 5 (Hz)

00.0 - 200

30.0

F33

Preset frequency 6 (Hz)

00.0 - 200

40.0

F34

Preset frequency 7 (Hz)

00.0 - 200

50.0

F35

Preset frequency 8 (Hz)

00.0 - 200

60.0

F36

Jog frequency (Hz)

00.0 - 200

05.0

«
...
51
52
53
54
55
...
»

Содержание 7300EV






























































































Отзывы:

Нет отзывов