manualshive.com logo in svg

TECO 7300EV, Быстрый старт, Страница: 25 / 93

Поделиться
Скачать
TECO 7300EV Скачать руководство пользователя страница 25

Chapter 3  Environment description and installation  

3-15

Over load protection Inverter rated current  150%/1min 

International 
conformity 

UL/CE

Over voltage 

200V Class: DC voltage >400V  400V Class: DC voltage >800V 

Under voltage 

200V Class: DC voltage <190V  400 Class: DC voltage <380V 

Instantaneous power 
loss  restart 

Set to enable or disable 

Stall prevention 

ACC/DEC/ Operation stall prevention and stall prevention level. 

Output terminal 
short circuit 

Electronic circuit protection 

Other fault  

Electronic circuit protection 

Protective F

unctions 

Other function 

Over current, over voltage, under voltage, over load, instantaneous power loss 

restart, ACC/DEC/ Operation  stall prevention, output terminal sort circuit, 
grounding error, reverse limit, directly start as power on and fault reset limit.

※

Note1: The setting resolution of above 100 Hz is 1Hz when controlled with operation 

keypad, and 0.01 Hz when controlled using computer(PC) or programmable 
controller(PLC).

Not

※

e2: EV-1P2~101-H1

；

2P2~201-H1/H3

，

401~403-H3 type (Fc=10KHz) with option filter can 

accordance with EN61800-3 first environment restricted distribution. 
EV-202~203-H1/H3 type (Fc=10KHz) with option filter can accordance with EN61800-3 
first environment unrestricted distribution. 

  EV-2P2~201-H1F type (Fc=10KHz) & EV-202~203-H1F type (Fc=6KHz) with Build in 

filter can accordance with EN61800-3 first environment unrestricted distribution. 

                  (IP65)  EV-2P2~403-H1(3)FN4(S)  series  &  EV-401~403-H3F  type  (Fc=10KHz)  with 

Build in filter can accordance with EN61800-3 first environment restricted distribution. 

Содержание 7300EV






























































































Отзывы:

Нет отзывов