manualshive.com logo in svg

TECO 7300EV, Быстрый старт, Страница: 72 / 93

Поделиться
Скачать
TECO 7300EV Скачать руководство пользователя страница 72

Chapter 5 Trouble shooting and maintenance 

5-4

5.1.2 Set up& Interface Errors. 

Display Error 

Description 

Zero speed stop 

It happens as set frequency <0.1Hz 

Fail to start 

directly

1. If the inverter is set to external control mode (F04=001), and 

direct start is disabled (C09=001), the inverter cannot be 
started and will flash STP1 when Run switch is in ON 
position when applying power (see descriptions of C09). 

2. Direct start is possible when C09=000. 

Keypad

emergency stop 

1. If the inverter is set as external control mode (F04=001)

，

the inverter will stop according to the setting of F9 when 
stop key is pressed. STP2 flashes after stop. Turn the Run 
switch to OFF and then ON again to restart the inverter. 

2. If the inverter is in communication mode and Stop key is 

enabled, the inverter will stop in the way set by F9 when 
Stop key is pressed during operation and then flashes STP2. 
The PC has to send a Stop command then a Run command 
to the inverter for it to be restarted. 

External

emergency stop 

The inverter will decelerate to stop and then flashes E.S. when 
there is an external emergency stop signal via the 
multi-function input terminals(see descriptions of F11~F14). 

External base 

block

The inverter stops immediately and then flashes b.b. when 
external base block is input through the multi-functional input 
terminal (see descriptions of F11~F14). 

PID feedback 

broken

PID feedback signal circuit error detection 

REMOTE

KEYPAD cable 

broken

1. REMOTE  KEYPAD does not connect with REMOTE 

KEYPAD, such signal will be displayed. 

2. REMOTE  KEYPAD connects with main KEYPAD, such 

signal will be displayed. 

3. REMOTE  KEYPAD and main KEYPAD both display such 

signal means communication errors. 

b.b.

  PID 

———

SP2

E.S.

SP1

SP0

Содержание 7300EV






























































































Отзывы:

Нет отзывов