manualshive.com logo in svg

TECO 7300EV, Быстрый старт, Страница: 83 / 93

Поделиться
Скачать
TECO 7300EV Скачать руководство пользователя страница 83

Chapter 6 Peripherals 

6-1

Chapter 6 Peripherals Components 

6.1 Input side AC reactor 

input side AC inductance 

Model

Current (A) 

inductance (mH) 

2P2/2P5-H1(F)/H3

5.0 2.1 

201-H1(F)/H3 5.0 

2.1 

202-H1(F)/H3 19.0 

1.1 

203-H1(F)/H3 25.0 

0.71 

 

 

 

401- H3(F) 

2.5 8.4 

402- H3(F) 

5.0 

4.2 

403- H3(F) 

7.5 

3.6 

JNEV-XXX-

HXX

 

 

 

6.2 EMC filter 

The inverter adopts rapid switching components to improve the efficiency of the 
motor and to reduce the motor noise. Using the EMC Filter allows the EMI 
(Electromagnetic Interference )and RFI(Radio Frequency interference)to be 
controlled within certain range. 

EMC standard 

The inverter with filter can comply with EMC standard 89/336/EEC on electro-
magnetic interruption and radio interruption. The inverters with filter have passed 
following test and comply with the specified standard.  

EMI radio standard and EMS immunity standard: 
EN 61800-3 1996/A11: 2000 

：

First Environment Unrestricted Distribution. 

EN 61800-3 1996/A11: 2000 

：

First Environment Restricted Distribution. 

Содержание 7300EV






























































































Отзывы:

Нет отзывов