TECO 7300EV Скачать руководство пользователя страница 74

Страница: 74 / 93

Chapter 5 Trouble shooting and maintenance

5-6

5.2 General functional troubleshooting

Status Checking

point

Remedy

Is power applied to L1, L2, and L3(N)

terminals (is the charging indicator lit)?

Is the power applied?

•

Turn the power OFF and then ON

•

again.
Make sure the power voltage is

•

correct.

Make sure screws are secured

•

firmly.

Are there voltage outputs in T1, T2, and
T3 terminals?

Turn the power OFF and then ON

•

again.

Is the motor mechanically overloaded?

Reduce the load to let the motor

•

running.

Are there any abnormalities in the
inverter?

Is forward or reverse running command
issued?

See error descriptions to check wiring
and correct if necessary.

Is there an analog input signal?

•

Is analog frequency input signal
wiring correct?
Is voltage of frequency input

•

correct?

Motor can not

run

Is operation mode setting correct?

•

Operate operations through the
digital panel

Are wiring for output terminals T1, T2,
and T3 correct?

Wiring must match U, V, and W

•

terminals of the motor.

Motor runs

inversely

Are wiring for forward and reverse
signals correct?

Check wiring are correct if

•

necessary.

Are wiring for output terminals T1, T2,
and T3 correct?

Check wiring are correct if

•

necessary.

Is the setting of frequency command
source correct?

Check the operation mode setting

•

of the operator.

Motor runs

inversely

The motor

speed can not

vary

Is the load too heavy?

Reduce the load.

•

Is the setting of operation mode correct?

Confirm the motor’s specifications.

•

Is the load too heavy?

Confirm the gear ratio.

•

Motor running
speed too high

or too low

Are specifications of the motor (poles,
voltage…) correct?

Confirm the highest output

•

frequency.

Is the gear ratio correct?

Reduce the load.

•

Is the setting of the highest output
frequency correct?

Minimize the variation of the load.

•

Increase capacities of the inverter

•

and the motor.

Motor speed

varies

unusually

Is the load too heavy?

Add an AC reactor at the power

•

input side if using single-phase
power.

Check wiring if using three

•

-phase

power.

Содержание 7300EV






























































































Результаты поиска

Содержание 7300EV

Отзывы:

TECO 7300EV, Быстрый старт, Страница: 74 / 93

Результаты поиска

Содержание 7300EV

Отзывы: